Shop
Community
Home
Forums
New posts
Search forums
What's new
New posts
New media
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
New media
New resources
Latest activity
Menu
Log in
Register
Install the app
Install
Home
What's new
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Latest activity
What's new
New posts
Latest activity
C
cgc0408
reacted to
kccoe's post
in the thread
Sx-m outdrive separating lower and upper unit
with
Like
.
No Title Seal on the raw water pickup tube is toast. Impellar pump sucking air while on plane.
Aug 27, 2026
C
cgc0408
reacted to
kccoe's post
in the thread
Sx-m outdrive separating lower and upper unit
with
Like
.
I got the info I needed. I have a appalachian engineer outdrive jack and stand. Gently clamp lower unit down on jack and remove the 6...
Aug 27, 2026
C
cgc0408
reacted to
kccoe's post
in the thread
Sx-m outdrive separating lower and upper unit
with
Like
.
Does someone have video or procedures of separating lower unit from upper unit transmission for a Sx-m 1.60 year 2003? Do you have to...
Aug 27, 2026
ezbtr
reacted to
FLATHEAD's post
in the thread
rant
with
Like
.
When I was 16 years old and was finally able to drive to a job. One of my first jobs was cutting grass at a huge apartment complex, 37...
Aug 27, 2026
J
jlh3rd
replied to the thread
cupped prop question
.
I said.. I want 6000 when I'm empty....not with 9 people. the question was does a cupped prop decrease rpms , everything else being equal.
Aug 27, 2026
alldodge
reacted to
bakerjw's post
in the thread
Repair of door latch
with
Like
.
Can you get access behind it? Do you have some resin on hand and glass? I'd fabricate a backer plate and see if I could fish it in...
Aug 27, 2026
J
jlh3rd
replied to the thread
cupped prop question
.
".....and the peak of the torque curve is usually much lower than the max RPM point..." torque/rpm ....curves/graphs ...show rpm and...
Aug 27, 2026
alldodge
replied to the thread
cupped prop question
.
(making number up) So if you have 9 people on the toon and it's getting 2.5 MPG at 5500 rpm that is not relevant because you want to...
Aug 27, 2026
B
bakerjw
replied to the thread
Repair of door latch
.
Can you get access behind it? Do you have some resin on hand and glass? I'd fabricate a backer plate and see if I could fish it in...
Aug 27, 2026
Scott Danforth
replied to the thread
cupped prop question
.
Then pitch down 2", and control the throttle with your right hand. You will be a tad high lightly loaded and not lugging it moving 9 people
Aug 27, 2026
J
jlh3rd
replied to the thread
cupped prop question
.
not speed or efficiency.... if I put 9 people on my pontoon I like seeing my motor running at the higher rpm.
Aug 27, 2026
Scott Danforth
replied to the thread
Boats from work.
.
Don't look in the bilge....deny deny deny
Aug 27, 2026
alldodge
posted the thread
Repair of door latch
in
Boat Restoration, Building, and Hull Repair
.
Suggestions on how to repair the latch hole? Yes this is my Craparral where looks like they used a drill bit to cut the hole instead of...
Aug 27, 2026
M
Mc Tool
replied to the thread
Just cant figure this out...
.
I just disconnect the fuel hose at the motor and either run it out of fuel or drain the carbs ....🙄usually both 😁
Aug 27, 2026
M
MikeSchinlaub
replied to the thread
Boats from work.
.
Ground everything in prep for the floor, made and glassed in a center stringer for extra support. Apparently, the owner and his brother...
Aug 27, 2026
Home
What's new
Top