Wiring Help Needed!!!

rroop32

Recruit
Thread starter
Joined
May 16, 2011
Messages
5
59zyi1.jpg


gauges dont work, figured i'd start with the Tach. I found this connection after i pulled the dash panel out. I looked around but could not find where this connection goes to?

Any suggestions.?

This is a 2004 Starcraft Pontoon out fitted with a 2002 merc. 60hp
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Wiring Help Needed!!!

The gauge you show is the SPEEDOMETER. It has no electrical connection except for 12 volts and ground for the internal light. Tachometers have four connections. 12 volts with key on. Ground, light, and sense. Question: Are four wires connected to the back of the tach? If not, which one(s) are missing. Also be aware that if the rectifier/regulator on your engine is bad the tach will likely not work and that means the charging system is also not working. If your boat has a VOLTMETER -- what does it read at idle and about 1/3 throttle (not in neutral please).
 

sw33ttooth

Chief Petty Officer
Joined
Apr 24, 2011
Messages
498
Re: Wiring Help Needed!!!

i have a few dead ends simmiler to that on my dash for extra add-ons dont see a brand name on gauges from that view guessing they light up your tach should have a ground which is one of the big studs on the back of the gauge and that is black.

then there should be a blue wire which is lights either solderd unto the light bulb or next to the light.

then there will be purple which is ignition goes to another stud.

for the most part it should be labled on the guage however from factory the way they wire i would check all your purple and black wires makeing sure there all tight and connected. might help to have an accual picture of the back of the dash so i could discribe it better
 

rroop32

Recruit
Thread starter
Joined
May 16, 2011
Messages
5
Re: Wiring Help Needed!!!

silvertip, please refer to the gauge on the right :facepalm:
 

rroop32

Recruit
Thread starter
Joined
May 16, 2011
Messages
5
Re: Wiring Help Needed!!!

at the time I took the picture the battery read 7.1 v. my voltmeter starts reading at 8 so i didnt get a reading on that anyway. battery is currently on the charger and will take a look tomorrow.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Wiring Help Needed!!!

silvertip, please refer to the gauge on the right :facepalm:

Had to reduce the VIEW to 75% to see the entire picture. If your gauges do not have a two pin connector like the one you show, that connector is obviously not for the tack. Battery voltage at 7 volts will also not light anything up. I go back to looking at the back of the gauge. If four wires are there none are missing. If any of the other gauges fail to work, look for missing +12 volts and ground. You can also look at the stickies at the top of this forum for a generic boat wiring diagram.
 

rroop32

Recruit
Thread starter
Joined
May 16, 2011
Messages
5
Re: Wiring Help Needed!!!

the connector pictured is off the Tach. Those two wires from that connector (blue/Black) go to the back of the gauge.
 

Sixmark

Master Chief Petty Officer
Joined
Jul 11, 2010
Messages
890
Re: Wiring Help Needed!!!

Well you are going to have to get a meter out and test those leads to find out where they go unless you have a wiring diagram for the boat.
 

sw33ttooth

Chief Petty Officer
Joined
Apr 24, 2011
Messages
498
Re: Wiring Help Needed!!!

blue and black wires togather like that tell me ground and lights your missing sender and 12 v+. not sure on sender color it will have a stripe on it i think and 12 v+ is ingintion which is purple again another picture of the back may be of more help then the front of the gauge which tells us nothing.
 

NYBo

Admiral
Joined
Oct 23, 2008
Messages
7,107
Re: Wiring Help Needed!!!

the connector pictured is off the Tach. Those two wires from that connector (blue/Black) go to the back of the gauge.
Those would probably be the wires for the light(s) in the tach.
 

Sixmark

Master Chief Petty Officer
Joined
Jul 11, 2010
Messages
890
Re: Wiring Help Needed!!!

and again I will add that they will need to be tested, and will need to be mapped out to find out where exactly they go in the boat in order to verify there are no breaks, shorts, etc.
 
Top