wire to ignition

harry57

Cadet
Thread starter
Joined
Jul 20, 2006
Messages
6
I purchased a minn kota dc battery charge from cabelas. ez hookup they said.
I received it and found i need to connect a wire to the ignition to make it go.
I have a 2003 merc on a pontoon with merc remote control box. It has a sealed
harness to the engine, a short harness with a tach connecter on the end. and
about 7 wires hanging loose. One is purple. I connected to it but doesn't seem to have voltage whether the key is on or off. What kind of signal or voltage
is the wire from the battery charger looking fo ?. I called minn kota but no
help from them. any help would be greatly appreciated. Harry
 

flargin

Chief Petty Officer
Joined
Aug 13, 2008
Messages
540
Re: wire to ignition

Is this a on-board battery charger? If so, mount it and connect it directly to the battery... any of the wires up front will not be a good idea to connect this too, too many ramifications.

If not, maybe a little more help of what make/model it is...
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: wire to ignition

You do not need to connect anything to the ignition on any on-board charger I've seen. But then we have no idea what charger you bought so a model number would help. It may be that you also bought something that is not what you had in mind for the problem you are trying to solve. Please provide details on what this charger is supposed to do. -- in other words -- why are you adding it.
 

harry57

Cadet
Thread starter
Joined
Jul 20, 2006
Messages
6
Re: wire to ignition

Thanks for the replies. This is a minn kota on board charger mk1. instructions
say for this dc alternator charger to function find the purple iginition wire and
connect it to the iginition circuit. This can be any +12v source that is only
energized when iginition key is turned on.

After reading your replies apparently this is the off-on for the charger. It
has a green light to indicate the charger is functioning. So, I should be able
to connect to red side of battery. If it need to be turned off to keep it from
running down the battery, just put an on-off switch.

Am I on the right track?
swi
 

harry57

Cadet
Thread starter
Joined
Jul 20, 2006
Messages
6
Re: wire to ignition

did not make myself clear. This charger has red and black leads to the starter
battery and red and black leads out to the trolling battery. There is an additional purple wire about 16ga. The hook up on this wire is confusing
 

flargin

Chief Petty Officer
Joined
Aug 13, 2008
Messages
540
Re: wire to ignition

Looking at this website, this is not a charger, it is essentially a 12v relay combiner from the starting battery to a house battery. Is that what you intened to buy?

Essentially, when you have your boat running, the relay will transfer voltage from the starting battery to the house battery.

However, it sounds like it has a +/- for starting motor, and +/- for the trolling motor, plus a purple wire.

Take the purple wire and attach it to the matching purple wire on your ignition coil, and attach the respective +/-. If you have a Mercruiser I/O it will be purple. If you have an outboard, I do not know what color it would be.

Essentially, this needs some voltage to turn on the charger. the design is when you turn on your key, that supplies 12v to the engine (i.e. the purple wire) and then that will turn on the MK1. Anything that has power when the switch is on can be used to activate this unit. Do not connect it to the + on the starting motor, this will essentially make it into a parallel connection, you would be better buying a $5 cable.
 

flargin

Chief Petty Officer
Joined
Aug 13, 2008
Messages
540
Re: wire to ignition

Thanks Flargin and Silvertip for your help with my battery charger and the
purple wire. I also have a tach that needs to be connected to the purple wire
in the remote box. Is this and the battery charger overload the on-start
switch which I assume feeds power to the purple iginition wire?

(posted from second thread

Harry,
you should be fine using the purple for the purpose of the tach and your chargers' trigger switch.

if you look at one of SilverTips stickyed thread, you will see the purple wire is normally used to power all of the guages, so the tach should be fine. The MK1 charger you have should not take much power.

However, if you start to have problems, I would remove the MK1 first in your troubleshooting.
 
Top