Upgrade to 4bbl, what about throttle cable bracket?

[findinghomer]

Upgrading my engine from 5.7 SBC 2BBL non vortec , to 97 and up vortec. , the 8 bolt manifold just got here today that fits 4bbl carb bc I wanted to upgrade from 2bbl. My question, is how will my throttle cable bracket with my circuit breaker and solenoid mount to the new carb? The bracket slid right over the to bbl mounting studs which are going to be much more narrow than the four BBL. Does it just not and I have to get a new bracket, or do I have to modify something? Appreciate your feedback, just putting together my plan for when my engine gets here, thanks

 

[Scott Danforth]

get the mercruiser 4-barrel bracket or one of the much much much less expensive generic 4-barrel throttle brackets and make up a new bracket to mount the circuit breaker.

 

[findinghomer]

get the mercruiser 4-barrel bracket or one of the much much much less expensive generic 4-barrel throttle brackets and make up a new bracket to mount the circuit breaker.

Is this it? Part number 805359T
Or is there one that looks like my bracket, but it's wider to fit the four barrel?

 

[Scott06]

Is this it? Part number 805359T
Or is there one that looks like my bracket, but it's wider to fit the four barrel?

yes that is it I used it for the same thing when converting from 2 bbl mercarb to a edelbrock 1409. the solenoid and Cb mounted perfectly.

What carb are you running?

I was able to take the parts (stud) off the throttle arm on the old carb to mesh with the throttle cable , just had to adjust the cable a touch (make sure it closes the throttle fully). I also used the throttle return spring that merc uses on the 357 alpha crate engines -

https://www.marineengine.com/parts/mercruiser-sterndrive-parts/357-alpha-4v/1g400000-up/carburetor-and-throttle-linkage

Made for a nice clean factory type installation

 

[findinghomer]

yes that is it I used it for the same thing when converting from 2 bbl mercarb to a edelbrock 1409. the solenoid and Cb mounted perfectly.

What carb are you running?

I was able to take the parts (stud) off the throttle arm on the old carb to mesh with the throttle cable , just had to adjust the cable a touch (make sure it closes the throttle fully). I also used the throttle return spring that merc uses on the 357 alpha crate engines -

https://www.marineengine.com/parts/mercruiser-sterndrive-parts/357-alpha-4v/1g400000-up/carburetor-and-throttle-linkage

Made for a nice clean factory type installation

Great! Thanks for your help and advice, but I don't have the carb yet but I'm thinking I'll get the 1409

 

[Scott06]

Great! Thanks for your help and advice, but I don't have the carb yet but I'm thinking I'll get the 1409

That would be my choice will bolt up nicely and work well out of the box.

The eddelbrock is the same as the webber carb Merc used from the factory and the same carb as shown in the parts breakdown I linked, so it will bolt in and look factory. Only difference will be the OEM carb is $1200 and the eddy is much less.

 

[Bondo]

Great! Thanks for your help and advice, but I don't have the carb yet but I'm thinking I'll get the 1409

Ayuh,.... A wise choice,.....

 

[Pmt133]

I also was going to do the 1409 on my 4.3. I did luck out and got a 4.3 carb from a friend off his V6 in a fair trade for a bottle of wine. One calibration kit and one tank and rebuild later and all is well. The 1409 is the better choice if you don't have that option for sure.

 

[Scott Danforth]

I'm sitting here looking at my pile of holley carbs..... I'm not a fan of Edelbrock carbs

 

[Scott06]

I'm sitting here looking at my pile of holley carbs..... I'm not a fan of Edelbrock carbs

the fact that you can use factory throttle bracket etc for a clean install makes sense for the OP.

A lot of guys like holleys but if they were so great why is there a pile of them not on engines... just poking fun as eddy carbs seem to elicit a response from holley guys... the three I have used ( 2 cars and 1 boat) have all been great and are still installed

 

[Scott Danforth]

The pile is because I keep buying them for future engine builds and I swap a lot of parts

The HP-950 is ready for my 7500 rpm LS build. The HP830 is currently on the 468 and will most likely get a larger main body and throttle plate. The 4777 650 cfm is for the next V6 build. The 750 vac secondary is rebuilt and ready for the wife's jeep build

 

[Pmt133]

I'm sitting here looking at my pile of holley carbs..... I'm not a fan of Edelbrock carbs

I really like holleys, have them on performance stuff, but holy hell do they constantly need adjusting on what I have them on. The holley 4000 I have runs as well as efi, so thats a lie. For daily and mild stuff, hands down prefer the AFB. Set it and forget it. And holleys QC on their new stuff would lead me to think Helen Keller was their supervisor. Got a 650 double pumper I want to slap on something fun. Maybe a stroked 400 pontiac.