Trolling motor question

Muddy41

Cadet
Thread starter
Joined
May 22, 2011
Messages
6
I have a issues with my Minnkota Maxium that when I am trolling aroound I have no issues seeing under water using my Lowrance LCX-17M. But when I go to move using my big motor I no longer can see under water. I lose view but when I slow down and go to use the trolling motor again I have no issue seeing under water again.

It is just when using the main motor that I cannot see underwater.

Anyone have a idea of what is wrong. Is something not set up right is my transducer messed up. Neew some help please.

Thanks
Mike
 
D

DJ

Guest
Re: Trolling motor question

How fast are you going when you lose your view?
 

Muddy41

Cadet
Thread starter
Joined
May 22, 2011
Messages
6
Re: Trolling motor question

Pretty much right from the start. As soon as I bear down on the arm I weem to lose the bottom on my screen. But as soon as go back to just sitting in the water and trolling it works.
 

EddiePetty

Lieutenant Junior Grade
Joined
Aug 25, 2008
Messages
1,008
Re: Trolling motor question

Mike,
If your fish-finder becomes erratic underway with the main motor, I suspect the tranducer is picking up air bubbles from the exhaust/ventilation plate/transducer mount.
Just for grins, raise the trolling motor sufficently to blow bubbles beneath the hull and see if you encounter the same problem.
 

fishrdan

Admiral
Joined
Jan 25, 2008
Messages
6,989
Re: Trolling motor question

Where/how is the transducer mounted? A picture would be helpful.
 

Muddy41

Cadet
Thread starter
Joined
May 22, 2011
Messages
6
Re: Trolling motor question

Mike,
If your fish-finder becomes erratic underway with the main motor, I suspect the tranducer is picking up air bubbles from the exhaust/ventilation plate/transducer mount.
Just for grins, raise the trolling motor sufficently to blow bubbles beneath the hull and see if you encounter the same problem.

I will give that a try. Thanks for that.

Just seems wierd even when driving 20mph you would think that I should be able to see and follow bottom.

THanks
Mike
 

Ray1958

Cadet
Joined
Aug 10, 2010
Messages
29
Re: Trolling motor question

Perhaps your transducer is mounted on the trolling motor? When you pull the trolling motor up to move, it is no longer in position to read the bottom ... I've done sillier things than that and laugh about them all the time.

Ray
 

Muddy41

Cadet
Thread starter
Joined
May 22, 2011
Messages
6
Re: Trolling motor question

Perhaps your transducer is mounted on the trolling motor? When you pull the trolling motor up to move, it is no longer in position to read the bottom ... I've done sillier things than that and laugh about them all the time.

Ray

I hear you on that one Ray.. But I have this one mounted in the back close to the bottom. I do have one on the trolling motor but that is not the one in question. I will see if I can put a pic up tomorrow showing where it is and how it sit currently.

Thanks to all so far.
Mike
 

Rick.

Captain
Joined
Jul 30, 2006
Messages
3,740
Re: Trolling motor question

You said, "I have a issues with my Minnkota Maxium that when I am trolling ..." This is a bit confusing as when i read the rest your issue seems to be with your gas motor and not your trolling motor unless I'm just not getting it. With the gas motor running in neutral, at high revs., do you loose the fish finder display? The reason I ask is when I installed my HumminBird there was something in the instructions that said not to run the transducer wire too close to the engine wires as it could cause problems/interference. I'm just wondering if your experiencing that condition. Best of luck. Rick.
 

Muddy41

Cadet
Thread starter
Joined
May 22, 2011
Messages
6
Re: Trolling motor question

You said, "I have a issues with my Minnkota Maxium that when I am trolling ..." This is a bit confusing as when i read the rest your issue seems to be with your gas motor and not your trolling motor unless I'm just not getting it. With the gas motor running in neutral, at high revs., do you loose the fish finder display? The reason I ask is when I installed my HumminBird there was something in the instructions that said not to run the transducer wire too close to the engine wires as it could cause problems/interference. I'm just wondering if your experiencing that condition. Best of luck. Rick.


You are so correct I screwed up. Some how my brain and fingers typed my trolling motor when it should have been my Lowrance LCX-17M. Very sorry to all that are trying to help.
 
Top