Super Sea Horse 33 Electric

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Help! I have little to no hair left to pull out!

I recently acquired the subject outboard. Currently I cannot get any water to flow out of the engine cooling spout.

I have removed the lower unit, verified good empeller, verified correct assembly/reassembly (three times), submerged the LU to approx 3" over water intake, all to no avail.

Is there a thermostat in this engine? In the part's manual there is no mention about one, but I can't figure anything else as the issue.

Any and all assistance would be GREATLY appreciated in that, as stated, I have no more hair to pull out!
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
Re: Super Sea Horse 33 Electric

First a model number would help with determining what year we are talking about here.

Also, the water pump itself has to be submerged beneath the water line, simply submerging the intake is not enough. The pump is not self priming.
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

The Model #: RXEL-15S; reseach indicates it's a '67

I meant to convey the lower unit is submerged up to what I would call the lower main mount. I first was using 'rabbit ears' to no avail; then I tried a container that simply covered the water intake port but after reading the numerous posts indicating similar problems until the boat was put into the water I obtained a deeper container that covers half-way up the LU.

I was reading that if the empeller was installed 'backwards' it would self correct, but I verified anyway. I verified all tubes/ports and waterways were clear yet I can still not get any water to flow.

I'm sure I'm missing something very simple but I can't find it.

Thanks for your help on this.
 

kfa4303

Banned
Joined
Sep 17, 2010
Messages
6,094
Re: Super Sea Horse 33 Electric

Hi fshhunter. Welcome to iboats. I had a '66 33 hp, so maybe I can help. For starters, there is no thermostat on this particular model. The 33 hp was sort of a budget version of the 35 hp. One of the things that made them cost a little less were the removal of features like the t-stat, but it's a non-issue as far as the water flow goes. I know you've been over the cooling system several times to no avail, but don't worry, we've all been there. The best thing to do is to start fresh and eliminate variable soon by one so you don't chase your own tail. Let's start at the bottom and work our way up. It sounds like you know how to drop the lower unit and inspect/replace the impeller, which is great. Do it one more time. A properly installed impeller should have fins which radiate backwards as the driveshaft spins clockwise (btw you should only ever spin the flywheel and/or driveshaft clockwise). When viewed from below they look like a series of "S" going around the hub. If you know for a fact that the impeller is brand new, then simply inspect it and reinstall it. Make sure you don't loose the impeller key. Without it the drive shaft will spin, but never engage the impeller. Once the impeller is reinstalled. Tug up on the shift rod to put the LU into FWD. Rotate the driveshaft clockwise and see that the propeller also spins clockwise. You should also be able to fell the impeller spinning smoothly within its housing. You can even see the hub spinning ivf ytou look at the top of the housing. Now press the shift rod all the way down and rotate the drive shaft clockwise again. The LU is now in REV, so you should see the prop spin counter clockwise (i.e. REV) while you spin the driveshaft by hand. Again you should be able to feel the impeller spinning smoothly clockwise along with the driveshaft. A bit of vaseline can help when installing a new impeller. Once the impeller is properly installed and you've confirmed that that FWD-N-REV are working, move on to the copper water uptake tube inside the exhaust housing. Give it a wiggle to see if it is properly seated in its upper gromet. If it is loose, you may just need to push it up a bit to seat it properly. Once it is seated correctly hold a garden hose at med-hi pressure up to the copper water uptake tube and see if water comes out of the main exhaust port. If the water flows out freely, then you passages are clear and you should be ok to reassemble the lower unit. If you do not get any water flow out, or if it is very weak, then you may have a blockage some where in the power head. If that is the case you 'll need to remove the head gasket to inspect the passages themselves. Assuming you get good water flow out of the exhaust, go ahead and reassemble the lower unit. Take special care the the copper water uptake tube seats properly into the top of the water pump housing. It is very common for it to not seat quite right, which then impairs the overall water flow. Try these tricks and give these links a read and let us know what you find. Keep us posted.

http://www.duckworksmagazine.com/04/s/columns/max/24/index.cfm

http://www.iboats.com/mall/partfind...4106=33&gd_search_14107=&**********=961434882
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

Thanks for the great advice. Of what you mentioned the one thing I didn't do was put a water hose on the copper pipe - I used air....I know...I know...not the same...

I'll get right on starting from the beginning and let you know. Again, thanks for the great advice and, for the record, I love this site - I have spent hours on it since getting this enginer and have learned a tremendous amount!

thanks
cliff
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

Well...tore it down, reassembled it, had water where I should have water...sort of.

When I put the hose on the copper pipe, I got some water out of the pee hole, which was encouraging, but when I put air on it there was great flow of air. Probably got a better seal on the air than water...but I digress...

After putting it back together, there was only steam coming out for a minute - presumably the residual water from the testing. But! there is good air flow when the engine is turning over coming out of the hole...just no water...[sigh]....

Am i mixing and matching simptoms/results? I am at wits end at the moment. Everything checks out yet there is no flow.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Re: Super Sea Horse 33 Electric

I suggest that you install a complete new water pump assembly..... housing, impeller, plate, screws, etc etc.. everything.

It sounds like you are assuming that the impeller is okay because it looks okay. That can really throw you. They can simply look good but be worn out, too flexible. Also scores in the water pump housing and plate will create air pockets, that sort of thing.

You're aware of where the water pump is.... the water level should be about 3" above the top of the pump area. It is not a self priming pump.
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

As you recommend is as I was thinking. There is no reason this should not work...the empeller is flexible, but didn't consider too flexible. I cleaned up the pump housing to ensure we had smooth surfaces...but again, as you state, I think the reason it doesn't work is because I am assuming too many things about this.

As for the water level, I read numerous posts about the water level not being high enough. This may be another assumption, but I have my water level up to the lower mount. I'm not sure how to get it higher without tossing the entire engine into the water...thought about it though!

On the way to the boat shop. I'll let you know how bad it hurts! :D
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
Re: Super Sea Horse 33 Electric

Test the water pump with the lower unit OFF the motor. Submerge it in a tub of water and turn the driveshaft clockwise with an electric drill, or just put a vise-grip on the shaft and turn it by hand. Water should come gushing out the water tube.
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

I'll try that...can't believe I didn't come up with that trick....

Re-tested all ports/tubes/etc. and water flows great through all. I put a hose on the pick-up tube and....SOMEONE SHOUD HAVE TOLD ME TO GET OUT OF THE WAY!!! :D Got a little wet on that one...

I put water in the output side of the pump and water flowed out everywhere - didn't get wet on that one though.

All this to say that, as has been said on many other threads, I think that empeller has to go...dispite how good it looks, bends, or fits! That's okay, I'm only on day three of getting the water pump to work!

Again, thanks for all the great input...and patience.
 

kfa4303

Banned
Joined
Sep 17, 2010
Messages
6,094
Re: Super Sea Horse 33 Electric

Cool. Sounds like you've found the culprit. At least now you know all of your passages are nice and clear. Finding a new impeller and replacing it shouldn't be too bad. Someone correct me if I'm wrong, but I think you could use a product like JB weld to fill in any gouges you may have in the housing, fix you think that may be an issue. While it may have taken 3 days to get this far it's still time well spent. Tinkering is fun and now you know all you ever wanted to know (and then some) about your motor's cooling system :) You can use all the same tricks (water hose, etc...) to test most other vintage OMC motors too. Congrats on the success thus far. Keep us posted.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Re: Super Sea Horse 33 Electric

Having the lower unit in water, then using an electric drill to crank the driveshaft? Yes, I seen a few guys do that BUT you'll never see me attempt it.

Water is an ideal ground, and a electric drill operates on 110/120 AC volts... you are only dead once!
 

kfa4303

Banned
Joined
Sep 17, 2010
Messages
6,094
Re: Super Sea Horse 33 Electric

LOL!!!! Yeah I'd stick with the vise grip/channel lock method. Better safe than sorry ;)
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

Alrighty then! Enough talk about a drill driven shaft that I can't figure out how you are hooking up the drill...not to mention I would have used a BATTERY drill....yeah, electricity and water seem to mix about as well as wives and girl friends...just sayin'...

Now on to the serious stuff....visited the boat shop - the word "no" seemingly hurts as bad from the parts guy as it does from the wife! No parts available locally. The good news is I got the all-clear on the impeller, but was chastised about the housing. Something about grooves kept coming up in the "why doesn't it work" discussion.

I like the idea about trying to either smooth or fill the grooves with JB weld in that it's going to take some time to get a replacement (by the way, not available through this site....darn it!) - nothing ventured, nothing gained I guess.

The long and short of it is this: I am NOT taking the LU off again without replacement parts - I can do it in my sleep I've done it so many times now - it appears the only problem that can cause my particular problem are the grooves...not that I believe it, but eliminate the obvious and whatever is left has to be considered....

Sooooooooo...I'll mix up my JB weld in the morning and carefully try and fill the grooves to see if I can get up and running until the new parts arrive.

Wish me luck and hopefully I won't blow this thing up before the new parts get here! :D


cliff
 

kfa4303

Banned
Joined
Sep 17, 2010
Messages
6,094
Re: Super Sea Horse 33 Electric

Keep us posted. Check sites like ebay, amazon, marineengine.com for hard to find parts. It's amazing what you can find there. Good luck.
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
Re: Super Sea Horse 33 Electric

I just bought the water pump kit for a 15hp for $50, so it wasn't that expensive. I believe the impeller alone was about $20.
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

Alright, Fellas, I think we may have learned something together here.

As an update, I have the water pump working as it should. First fix, since we last conversed, was to resurface the impeller housing - that didn't fix the problem. Second, I exhaustingly searched out the cheapest water pump repair kit I could find and ordered it - it'll be here next week. Then something dawned on me about all the water pump repair kits I looked at on the web...none of them had a concave bottom plate!

Yep, 20 minutes after I ordered an expensive repair kit, I pulled the bottom plate out of the water pump, carefully flattened it out again and...you guessed it...the water pump works fine!

So, hopefully we learned there is yet one other problem with water pumps other than the impeller and case - look at the bottom plate. I have no idea, and can't figure out, how the plate got the concave shape to it, but it pushes a lot of water now.

Thanks for all your assistance on this matter and I look forward to picking your collective brains on future problems with this toy!


cliff

PS
I knew it had to be something simple...and once again I found it was indeed something simple.....darnit!
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Re: Super Sea Horse 33 Electric

I checked the above posts. If you had mentioned the plate was concave, I bet one of us would have picked up on that.
 

fshhuntr

Cadet
Thread starter
Joined
Sep 22, 2011
Messages
12
Re: Super Sea Horse 33 Electric

Yeah, about mentioning the plate...that's what my post was intended to convey.

In all the posts I read about water pump issues, I never came across any that mentioned looking at the plate. Not having dealt with this kind of engine since the early eighties, it never dawned on me to look at that - or consider it might me the root of my problem.

Sorry if something else was conveyed, that was not my intention.


thanks again for all the help thus far.

cliff
 
Top