Stereo Upgrade - Battery Question

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
hi! I have a 20' Hurricane with a 150hp Yamaha FS. I want to add a 6 channel amp to power the four 60w speakers and one 200w subwoofer. In the configuration the amp will be set up in, it will be outputting 650w RMS, however, I don't think I will ever need to turn it up far enough to utilize that much wattage. I currently have two starting batteries on a switch. I don't really have any other electrical components other than the running lights for nighttime and a few other small items, but only if I switch them on.

I am thinking of maybe wiring my two starter batteries to switch one and wiring a new deep cycle battery to switch two. That way, I can use switch one when starting the engine and then switch to switch two when running and listening to music. I also intend on installing a 1.8f capacitor to help with peak power draws.

I am new to all of this however, so is any of that even necessary? or is there a better route I should take? Any ideas, suggestions etc would be great. Thanks!

taz
 

cr2k

Captain
Joined
Mar 19, 2009
Messages
3,730
Re: Stereo Upgrade - Battery Question

Sounds OK, just don't expect the OB to charge a battery like your car.
 

cpubud

Chief Petty Officer
Joined
Jun 18, 2008
Messages
468
Re: Stereo Upgrade - Battery Question

you would be better of using one battery strictly for a start battery and the 2 batterys to operate all the electronics and lights when at anchor.
 

Silverbullet555

Chief Petty Officer
Joined
Mar 13, 2011
Messages
621
Re: Stereo Upgrade - Battery Question

Skip the capacitor. Not worth it imho.

What size are your batteries now? What's their reserve capacity, etc?


I wouldn't bother with 2 starting batteries wired to one side. If there is no draw on it keep one on board and the other one at home charged.

Either use the second one as your house battery until it dies then replace it with something bigger or use something else for the house battery. For a long time, I ran 2 starting batteries. Stereo off of one, everything else off the other. I never drained the house battery in a day at the lake. Now I run 2 group 31 batteries with 190 minutes of reserve. My boat, in how we use it does not recharge the stereo battery. I charge it at home. Be prepared to do that.
 

fucawi

Banned
Joined
May 18, 2011
Messages
1,039
Re: Stereo Upgrade - Battery Question

You would be better to wire it up and then measure the current draw at normal volume to see what you need ..you will be supprised how little current you actually need 5w of power in the speakers in a normal living room will blow your head off ...which is what I would like to see happen to all boaters who run speakers on boats ...boom booom boom ....go away.
 

wellsc1

Petty Officer 1st Class
Joined
Apr 7, 2009
Messages
328
Re: Stereo Upgrade - Battery Question

I put a stereo in my Sea Chaser. It came with a wire to connect directly to the battery in order to maintain the memory of stations programmed and the clock. I like to completely disconnect the battery when storing the boat, so the memory is only active when the main battery switch is on; hence I depend on the station scan function a lot. It's not really functional, but I don't have to worry about any milliamp battery drain whatsoever when the boat is in storage or between long intervals between fishing trips. If others contributing to this thread advises otherwised, I'm open for changing it.
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

Thanks for all the replies guys! I will go check the specs on the current batteries I have this morning and report back. I actually don't plan on playing the stereo to often with the engine off. I just don't want to kill my batteries get stuck on the water. Do people with deep cycle batteries charge them at home? Is there a good battery charger you guys can recommend? thanks again!

taz
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

I actually have a 1-2-both switch. I'm not sure if it is a Perko switch (not sure if that is just the brand name or what) but I definitely have a switch that either runs everything off one battery, or the second battery, or both. How does that solve my issues though?
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Stereo Upgrade - Battery Question

You have so many options it will make your head spin. Using the switch is just one option. Consider this. Swap the smallest of the two current batteries with one large group 27 or 31 deep cycle. Make it BAT 2 on the switch. Keep the starting battery as BAT 1. Wire everything to the COM terminal of the switch. When docked, beached or anchored listening to the noise you select BAT 2. Underway use BOTH. While the outboard will not top off the batteries in anything less than a multi-hour wide open throttle run, it will add a bit depending on how fast and how long you run. Another option is an ACR. The starting battery gets priority from the charging system until it is topped off, then it switches to the deep cycle. Either way, you need either an on-board or portable smart charger to top off the deep cycle. A dual output charger would keep both topped off. Of course you could keep both systems totally separate for the ultimate in simplicity. No switch, no acr, no isolator and no charging of BAT 2 except at the dock.
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

Consider this. Swap the smallest of the two current batteries with one large group 27 or 31 deep cycle. Make it BAT 2 on the switch. Keep the starting battery as BAT 1. Wire everything to the COM terminal of the switch. When docked, beached or anchored listening to the noise you select BAT 2. Underway use BOTH. While the outboard will not top off the batteries in anything less than a multi-hour wide open throttle run, it will add a bit depending on how fast and how long you run. ...

Thanks! This sounds perfect! I'm looking at chargers for the batteries, are there any that you can suggest that are good for deep cycle batteries? I don't see many references to boat batteries or deep cycle batteries in the specs of the chargers. Will this one do the trick?

http://www.amazon.com/CTEK-Multi-Smart-Battery-Charger/dp/B000FQBWCY
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Stereo Upgrade - Battery Question

That unit looks more like a battery maintainer than a charger. An for $56 it's performance is questionable. Remember -- you have two batteries, one of which will be repeatedly deeply -discharged (when compared to the starting battery). ProMariner, Guest, MinnKota, and a host of others make "On-board: chargers with one, two, three, and even four sets of outputs. You need a two output charger with a minimum of 6 amps per output. Check right here on the iBoats Store for the various models.
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

So you think that I will need to manually charge the starting battery as well? I figured since the starting battery currently gets charged by the alt, then I would only need the charger for the deep cycle...
 

giericd

Petty Officer 2nd Class
Joined
Oct 1, 2011
Messages
102
Re: Stereo Upgrade - Battery Question

taz I was a MECP certified installer (moble electronic certification program) doing all kinds of custom car audio/securtiy systems on cars and boats. Do you all ready have the speakers you want to install? if not expecially in a marine system you want to look closely at the specs of the speakers! first of all make sure all items are marine grade, or they will corrode out fast (speakers, wires, crimps/connectors....) As stated above a cars charging system isn't like a boats charging system, if your car is running you should be getting real close to a constant 14.4v which is ok for car audio but we have all seen the cars driving down the street with the head lights that keep dimming from the eletrical drain the audio system is causing, in most cases a CAP will fix that problem but not all ways. Some marine charging systems from what i am learning might not even start charging untill you reach a certain RPM- that can be a problem with draining your battery(s) with the audio system. When you pick your speakers you want to look at the specs, look at the sensitivity! it tells you how power hungry your speakers are, for example the JL Audio 12w3v3-4 sensitivity is 87.15 (1w/1m) which means with 1 watt measured with an osciliscope at a distance of 1 meter it puts out 87.15db of sound. the JL Audio 12w1v2-4 is 86.81db (1w/1m) both subs have a peak power of 300w. that tells you that for the same amount of electricity used the 12w3v3-4 (87.15) is going to be slightly louder. now for your smaller speakers (mids and highs) those numbers will change but you want to compare several speakers with similar peak power and find the one with the highest db 1w/1m, that will be the most efficent speaker. most efficent doesn't mean best quality though, do some home work on what is in your price range then compare them from there. On all the boats like pathfinders, mako type boats I allways make sure the batt that powers the stereo is seperate from the starting batt! keep them seperate! it is so easy to get caught up in a few good songs in a row and keep telling your self "i'll shut it off after THIS song" next thing you know you turn the key and nothing happens. for some music while crusing around a starting batt and audio bat is fine, but if you are going to pull up on the beach like we do at the party spot here in Naples fl and keep the toons on for a while then have a starting batt, then 2 batts run in parallel with that that should give you a pretty good amount of time on the water with music, might be able to make it all day on that set up depending on output of amp and how hard you run it. (our shop had a precision power A1 art series amp(their most powerful amp at that time) we hooked up in my honda just to see what it could do. turned the power up to 3/4, started my car and threw in the bass mechanic test CD the first bass note hit so hard and the amp drew so much from my eletrical system it actually stalled my engine!)
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

wow! thanks for all the info! Yes, I've already purchased my gear and it is all marine certified. I am thinking of following SilverTip's suggestion of having a starting battery wired to switch position 1, and a deep cycle (meant for stereo) wired to switch position 2. Then I will use pos. 1 to start the boat and then switch to both batteries while cruising and listening to music, and then switch to pos. 2 when I am anchored listening to tunes. However, are you suggesting that I leave one starting battery on pos 1, and connect two deep cycles in parallel to pos 2? then I should leave the switch on BOTH while cruising so that all three batteries are utilized? My biggest concern is draining all my batteries and being stuck somewhere so what is the safest bet to prevent that? Thanks!
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Stereo Upgrade - Battery Question

Let's hit one topic at a time:

CHARGING: Did you not say you are worried about keeping things charged between long periods of storage? You did actually!!! That means the deep cycle AND the starting battery need to be kept fully charged and maintained. That also means if you have two batteries, you need a two bank charger (portable or on-board). If you have two batteries in parallel to operated on BAT 2, you can still get by with a two bank charger but it will take twice as long to charge both of those batteries. The engine should keep the starting battery charged but for long periods of storage, at least add a "maintainer" which is nothing more than a 1.5 amp output smart charger.

SWITCH USE: Your plan for use of the switch is ok. However, the engine alternator is not capable of keeping two batteries topped off so the chance for doing that with three is out of the question. So back to the portable or on-board charger. You simply need that -- no way around it.

CHARGERS: My personal preference for situations like yours is to iinstall a high output (10A minimum) single bank on-board charger for the deep cycle bank. Install a maintainer on the starting battery. The maintainer and single bank charger are less expensive than a 10A dual bank charger that will have one bank loafing most of the time so it is wasted capabilitiy. Besides, if one bank of a two bank charger goes bad you lost half the capacity. If you lose the single bank, it is less expensive to replace. On-board chargers are easy to install and you simply plug them in when at the dock. Smart chargers can be left on 24x7 with no ill effects on the batteries.
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

Thanks so much! great suggestions! If I keep a starting battery on BAT 1 and then wire two deep cycle batteries on BAT 2, the would I put the switch on BAT 1 to start the engine, and then switch to 1 + 2 when cruising around (so all three batteries are being utilized and somewhat topped off by the alt), and then switch to BAT 2 when listening to music while anchored? That should make sure that my starting battery at least is never discharged too low, yes?

and then of course I'll install an onboard charger as suggested and charge up whenever docked...
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Stereo Upgrade - Battery Question

Your plan for use of the switch sounds fine. However, you don't always need to switch to BAT 1 to start the engine. If you are moving around frequently (as in beach for half an hour, then move to another spot, repeat, repeat, repeat) you could just leave the switch on BAT 2 which leaves BAT 1 totally out of the picture. Starting the engine on the paralleled deep cycles will not suck much juice out of them and you wouldn't have to be flipping the switch all the time. That would also leave the just the deep cycles for the alternator to charge. Use the switch to your advantage by setting it to whatever battery needs the most help.
 

tazmajazz

Seaman Apprentice
Thread starter
Joined
Oct 14, 2010
Messages
40
Re: Stereo Upgrade - Battery Question

ok, just one more question. I purchased a Genius Smart Charger and plan on installing it by the batteries. the instrucitons are lacking much info. Do I leave the charger's leads attached to the batteries at all times whether or not it is charging or the boat is under way? Also, there are two additional posts coming out of the batteries, separate from the two posts that are currently connected to the boat. Do I connect the charger leads to these extra posts, or the same posts that are already connected to the boat equipment etc? Thanks again, this info is all very helpful :)

taz
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Stereo Upgrade - Battery Question

How about giving us some Genius Model info. We have no idea if this is a protable or an on-board charger. If you bought this one you bought the wrong one as it is a "maintainer" (way too little output for "charging" a single, deeply discharged battery much less two of them.

http://www.northerntool.com/shop/tools/product_200471371_200471371?cm_ite=19841&cm_pla=Auto Repair>Battery Chargers + Jump Starters&cm_cat=pricegrabber&cm_ven=Aggregates

If it is intended for permanent installation (an on-board unit) then yes, the leads are attached to either set of posts and yes, they stay connected even when the engine is running. Diodes in the charger prevent back feeding the charger from the alternator or the battery. If it is a portable unit with alligator clips then the charger should be removed when the boat is in use.
 
Top