Steering Problem 1987 Johnson 140 VRO

carsonclen

Recruit
Thread starter
Joined
Feb 9, 2009
Messages
1
My motor is very difficult to turn. The mechanic at our boatyard pointed out alot of rust on the column that runs from motor head down to the prop. I've changed the helm and steering cables.

Has any one had this problem, and do you have thoughts on how to solve it?

Thanks, carson
 

tashasdaddy

Honorary Moderator Emeritus
Joined
Nov 11, 2005
Messages
51,019
Re: Steering Problem 1987 Johnson 140 VRO

have you ever greased it. take it this is a salt water motor.
 

ezeke

Supreme Mariner
Joined
Sep 19, 2003
Messages
12,532
Re: Steering Problem 1987 Johnson 140 VRO

Have you tried turning the motor in both directions with the steering cable disconnected? What were the results? Have you greased all of the fittings?

It's very important to maintain all of the anodes on that motor all of the time if you are running it on the Chesapeake, otherwise the steel parts in the motor will deteriorate rather quickly.
 

ken52

Petty Officer 1st Class
Joined
Jul 27, 2008
Messages
307
Re: Steering Problem 1987 Johnson 140 VRO

Sorry I just found this thread. I have the same problem on my 87 140 Rude. I've tried different length cables with no luck. I was told this is a very torquey motor.

I'm looking at going to hydraulic steering to hopefully solve my problem!

Kenny
 

ezeke

Supreme Mariner
Joined
Sep 19, 2003
Messages
12,532
Re: Steering Problem 1987 Johnson 140 VRO

Before you change the steering, experiment with the trim tab. You need to turn the rear of the tab in the direction that the boat is pulling. Use small increments and keep track of the results. There is generally a sweet spot for your trim tab that will provide the best overall results. The trim tab works by deflecting water being thrown from the propeller.

The other thing that can make your motor pull off is not being centered perfectly perpendicular on the boat - not the top of the motor, but the gearcase and propeller.
 

Toy Yot

Cadet
Joined
May 8, 2009
Messages
7
Re: Steering Problem 1987 Johnson 140 VRO

My motor is very difficult to turn. The mechanic at our boatyard pointed out a lot of rust on the column that runs from motor head down to the prop.

I just found this thread and am in the middle of trying to resolve this same problem. My helm and cables are good and function freely. My Johnson 140 VRO is almost frozen in place and a lot of rust is evident on the tiller(?) arm that connects to the steering cable. I'm afraid the rust extends down that tube which is why the motor won't turn. I periodically grease the fitting on the side of that tube (saltwater use) but it has kept getting worse until I can only turn the motor with a pry bar. I have contemplated disassembling the motor and replacing that tube and the rusted tiller arm but so far I have been unable to find those parts anywhere nor can I find any info about repairing or replacing these parts. By the way the motor is a 1987 and still runs STRONG so I certainly don't want to replace the whole motor. Any help / info /suggesions would be greatly appreciated. Thanks, Dave
 

wburge14

Recruit
Joined
Jul 12, 2009
Messages
4
Re: Steering Problem 1987 Johnson 140 VRO

I am having same prob with 1986 Yamaha 150. Does anyone have a diagram of the pivot assembly? Can you give a description? Is there a bearing at the top and bottom, or just at the bottom? There is a zerk fitting near the bottom of the tube, but none near the top! I have greased the zerk fitting, but I only see old grease exiting at the lower bearing. Any help will be appreciated.
 

ezeke

Supreme Mariner
Joined
Sep 19, 2003
Messages
12,532
Re: Steering Problem 1987 Johnson 140 VRO

You might try disconnecting the fuel line and then heating the steering arm assembly where it enters the swivel bracket; it may soften the old hardened grease enough to allow some new grease to reach the bushing. The high setting on a hiair dryer is about as hot as you want to go.

On the 140 Loopers there is a split lower cowl that is very easy to remove to get it out of the way.

The rust on the steering arm is assembly is rarely as bad as it looks, but a lot of it is caused by failing to maintain the motors anodes.
 
Top