Spark plug for a 63 Evinrude

Ragtime

Recruit
Thread starter
Joined
Jul 9, 2003
Messages
3
I guys - I just recently purchase a 1963 75 HP Evinrude Starflite outboard on a wonderfully restored 1960 Carver. The engine runs fairly well at high speed and a little ruff at low speeds. My question is does anyone know the correct part number for the spark plugs for this engine. The engine Model number is 505298. My intent is to get the service manuals ASAP but for the time being I'd like get the correct plugs in. Right now it has Campion J6C installed and I'm thinking that this isn't correct. Any help would be greatly appreciated. Thanks mporrey@charter.net
Code:
 

ob

Admiral
Joined
Aug 16, 2002
Messages
6,992
Re: Spark plug for a 63 Evinrude

Welcome Ragtime.The correct sparkplugs for that engine are Champion J4C gapped at .030".
 

Ragtime

Recruit
Thread starter
Joined
Jul 9, 2003
Messages
3
Re: Spark plug for a 63 Evinrude

Thanks for the reply OB. It looks like I do have the wrong plugs in.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Re: Spark plug for a 63 Evinrude

Ragtime... OB is correct as always, however the J6C plug that you speak of is an alternative plug which sets at the same gap (.030).<br /><br />There are quite a few older engines that have a problem with the original plugs, very slight miss from time to time, that sort of thing. The J6C cures those minor problems most of the time. It's okay to use either plug.<br /><br />That engine should have fixed high speed jets and adjustable slow speed needle valves, in which case the following may be of interest to you.<br /><br />(Carburetor Adjustments - Older V/4 Downdraft Carb)<br /> <br />NOTE: The early model downdraft carburetors incorporated "Adjustable High Speed Jets". The later model downdraft carburetors used "Fixed High Speed Jets". Follow the below instructions accordingly. If you do not have adjustable high speed jets, ignore those paragraphs pertaining to same.<br /><br />Lift the center High Speed Control lever and turn it so that the point faces forward, resting on the high ridge. This will disengage the lever control gear from the individual high speed jets (slots). Have the slow speed needle valve knobs installed upside down so that they can be turned without encountering any obstruction.<br /><br />Gently seat each of the High Speed needle valves, then back each one out one (1) turn. Gently seat each of the Slow Speed needle valves, then back each one out one and one half (1-1/2) turns. NOTE... have the jam nut on the s/speed needles snug so that viberation won't have any effect on them, but loose enough so that you can turn them without a great amout of effort.<br /><br />(High Speed)<br />With a reliable person at the wheel, and one kneeling in front of the engine, start the engine (yes, it will run lousy with the above initial needle valve settings), put it into forward gear, and apply full throttle. Start with the High Speed adjustment on the left using a screwdrive that properly fits the slot.<br /><br />(High Speed Adjustments)<br />At full throttle, with the proper size screwdriver, slowly start turning one of the H/S needles in segments of 1/8 turn, waiting momentarily for the engine to respond, then repeat turning. You will reach a point where the engine will start to die out. At that point, back that needle valve out approximately 1/4 turn. Now, go to the other High Speed needle valve and repeat that procedure. At some point in that 1/4 turn out, you will find the smoothest high speed setting (you can now lower the throttle rpm). That will have both high speed needle valves set correctly, and at that point you can lift that center lever adjustment of that high ridge, keeping it lifted until the point is facing the engine, then lower it into its proper position. (When you turn that lever now, you're adjusting both High Speed needle valves at the same time.)<br /><br />(Slow Speed Adjustments)<br />Now, lowering the rpms of course, take the engine out of gear and set the throttle just to where the engine will stay running. Again, in segments of 1/8 turn, slowly start turning in one of the slow speed needle valves, waiting a few seconds between each turning for the engine to respond. As you turn the s/speed needles in, the rpms will increase..... and as it does, lower the rpms to where the engine will just stay running (otherwise the rpms will climb quite high). You will reach a point whereas the engine will either start to die out or it will spit back (sounds like a mjild backfire). At that point, back the needle valve out 1/4 turn. Repeat the process with the remaining slow speed needle. Again, at some point in that 1/4 turn out, you will find the smoothest setting. When finished, tighten the jam nut somewhat, then remove and reinstall the s/speed knobs correctly (right side up).
 

Ragtime

Recruit
Thread starter
Joined
Jul 9, 2003
Messages
3
Re: Spark plug for a 63 Evinrude

Joe - Thanks so much for the information. My engine appears to have fixed high speed jets. I probably will try to adjust the low speed jets as in the information you've provided. The engine seems to have a noticeable miss at low and lower midrange speeds. It runs quite smooth at high speeds and starts fine. I'd like to try to rule out all problems that if can fix easily before I start getting in to more complicated trouble shooting. If you have any other suggestions I would be most appreciative. Thanks
 
Top