Shift rod adjustment

Watermann

Starmada Splash of the Year 2014
Joined
Jan 12, 2013
Messages
13,860
Yeap you have to take that outer exhaust housing off and the inner as well since it will ruin the gasket they both use. Look up inside there with a flashlight and you can see where the tube goes. You also have to take the split ring off the bottom of that motor swivel to drop it down and off. You'll need a new gasket for that housing and a probably a new grommet for the water pipe.but I can;t seem to find one in stock any where I normally shop for parts on my old Johnny.

Greasy, grimey job but it's pretty easy.

Google the part number below
315861 ? GASKET, ADAPTER TO HOUSING
 

Ramsey1463

Cadet
Thread starter
Joined
Mar 24, 2016
Messages
29
No Title

So what am I doing wrong? I took every bolt I see off and the casing still won't come off. I undid the 8 bolts from the top, the 2 from on top of the casing near the back, took off 2 bolts each side on the split ring, and unscrewed the one that remains on each side as far as I can. Is there something I'm missing?
 

Attachments

  • photo241402.jpg
    photo241402.jpg
    93.1 KB · Views: 0
  • photo241403.jpg
    photo241403.jpg
    109.3 KB · Views: 0
  • photo241404.jpg
    photo241404.jpg
    82.7 KB · Views: 0

Watermann

Starmada Splash of the Year 2014
Joined
Jan 12, 2013
Messages
13,860
Did you take off the split ring that holds the assembly on the pivot shaft? It's on the very bottom of the shaft and is usually hidden in grease.
 

Ramsey1463

Cadet
Thread starter
Joined
Mar 24, 2016
Messages
29
I did not lol. I see the piece I believe you're talking about but I'm not sure how to take it off. Does it screw off or do I need to take a screwdriver and pop it off? I don't want to break it trying to take it off.
 

Watermann

Starmada Splash of the Year 2014
Joined
Jan 12, 2013
Messages
13,860
I don't know about a screw driver, I use my snap ring pliers. Would hate to ruin that ss ring, you may need to invest in a $6 set of pliers. Getting the ring back on is 'a snap' too!

Snap ring
snapring.jpg
686656.jpg
 
Last edited:

Ramsey1463

Cadet
Thread starter
Joined
Mar 24, 2016
Messages
29
Hopefully this is the last stupid question I have to bother you all with but I got the split ring off and it still won't drop. I wiggled the casing and it came down about an inch or so but the swivel is holding it in place. Is there another piece I need to undo on the swivel?
 

Ramsey1463

Cadet
Thread starter
Joined
Mar 24, 2016
Messages
29
I should clarify. I wiggled the upper casing on the lower unit and it came down an inch. Not the swivel.
 

Watermann

Starmada Splash of the Year 2014
Joined
Jan 12, 2013
Messages
13,860
The housing must be getting hung up, maybe on the bent up water pipe? Look up inside there and see if it is. If the housing dropped off of the shaft an inch there's nothing else I can think of that would be holding it on there.
 

Ramsey1463

Cadet
Thread starter
Joined
Mar 24, 2016
Messages
29
I took a rubber mallet and gently tapped it and got it to come off. I got everything back together and it seems to be in working order. Tested it out at home and it went into forward and reverse with no problem. I'm taking it out this weekend and hopefully all goes well. Thank you all again for all the help. You don't know how much I appreciate it.
 

Watermann

Starmada Splash of the Year 2014
Joined
Jan 12, 2013
Messages
13,860
Just returning the favors that were done for us at one time or another. Great to hear you accomplished a less than simple job by being a stick with it kind of guy :thumb:
 
Top