Sheared lower unit bolts 9.5 sportwin 1972

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
I picked up the motor yesterday in running condition. The rich/lean adjuster is siezed up in what I think is the more lean adjustment and I went to see what the impeller was looking like and wouldn't you know it, two bolts sheared off below the surface. The flange about 5 inches below the bolts is going to keep me from screwing anything in front directly above the bolt. Am I screwed at this point? I'm feeling pretty screwed.
 

Attachments

  • photo270668.jpg
    photo270668.jpg
    77.2 KB · Views: 0
  • photo270669.jpg
    photo270669.jpg
    58.8 KB · Views: 0

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Use heat to get the other 2 out.----The use heat to get the 2 broken ones out with a vicegrip once lower is off.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
So only one came out and the other 3 are brokenot off in there. The lower unit won't come off or budge at all. I tried hammering it loose but it just warps the flanges. I tried using a ratchet strap tied to the LU and securing the other half to a tree. I had some tension but realized that if it popped loose it would probably do bad things to the shift arm that would still be connected so I stopped.

I can't think of a good way to beat on it without totally messing it up or chipping it
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Lack of maintenance has likely allowed the driveshaft to become jammed in the crankshaft spline.-----Rust has that affect.-----Good luck with this project.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
Well I got it off. I used a block of wood cut at the right angle to share the load of the hammer across more area and it loosened up without bending the crap out of it. So I tried to get to the impeller and all 4 of those screws broke off. Awesome. So next step is to try and pry that thing apart. Anyone know if there's threads in the top half of the water pump housing? Guess I'll find out either way
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I always use heat where those screws thread into the housing and pump body to prevent prevent breakage.---There are no threads on the pump housing.---Corrosion products have jammed it up.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
Yes it looks like every bolt and screw thread has been tightly packed with dirty, off white flour ;)

I have been working on a 1959 35 johnson and I didn't realize how lucky l was with the lower unit. Everything must have been taken apart in the last few years or just very well lubed the last time it was done. Inside and out was pretty clean except for the one long bolt that goes from the top secton and through the middle and into the bottom. It had that same flour -like corrosion in the threads, but it was a beefy enough bolt that it didn't just tear apart like a snickers bar when I put on the pressure.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Chemistry 101----The white powder is ALUMINUM OXIDE= aluminum + oxygen.----That means there is now more material there as oxygen from the air has joined with the aluminum.---Nature packs it in there.---That is why things jam up.
 

cfauvel

Chief Petty Officer
Joined
Aug 16, 2005
Messages
645
Racerone,

would soaking the lower unit is a bath of water and baking soda or water and vinegar help?

My daughter states to bath in Diethyl Ether (aka ethanol). not rubbing alcohol (might want to test on something else that is corroded)
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
That is aluminum oxide---the same stuff sandpaper is made of. Nothing that I know of will dissolve it. I even asked my brother, who is a chemist and a rocket scientist (really). I told him that if he could come up with something, I'll market it and share the wealth. Nothing yet.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
No Title

So with the lower unit I was able to use a hammer and get downward force to separate the two halves. The housing I'm working on right now is got me stumped. The drive shafts is keeping my drill from being directly above the screw holes to drill them out. The bit went crooked and started eating at the aluminum of the housing. I've been trying to use a sharpened screwdriver bit as a chisel to get between the top and bottom but all that's done is dug into the soft aluminum and made no progress. I can't think of another way to get leverage on this thing. All the screws sheared below the surface so it's stuck as hell.
If I could just drill out the screws this wouldn't be a problem. Any ideas welcome!
 

Attachments

  • photo270822.jpg
    photo270822.jpg
    83.7 KB · Views: 0
  • photo270823.jpg
    photo270823.jpg
    72.4 KB · Views: 0
  • photo270825.jpg
    photo270825.jpg
    73.2 KB · Views: 0
  • photo270826.jpg
    photo270826.jpg
    70.7 KB · Views: 0

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
When all else fails, bust the sides of the pump housing away from the screws and remove it. Then deal with getting the rest of the screw out of the gearcase. You probably need a new pump housing anyway. Welcome to the world of salt-water outboard repair. Or whatever else that thing has been in.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
I just can't bust them away from the housing is the problem. I am really trying to save the 70 to 80 it cost for the new housing. I bought the 20 dollar impeller already. I know there's got to be a way to salvage it. I'm sure someone has had the same issue and figured it out. Maybe if I jb weld some sort of bar to the top so I can get leverage then just grind it off afterwards
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
You wrote: "I'm sure someone has had the same issue and figured it out". Well you are right on that score. Does 24 years in an outboard shop on the Gulf Of Mexico coast count? BTW, the pump housing is a lot cheaper than a gearcase, which is where you are headed.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
Well it runs fine and there's no water in the gear oil. Maybe I'll just leave it be and enjoy my 100$ toy while it's alive. I just thought I'd try to keep it from dying immediately with a broken impeller since it seemed like an easy enough and cheap enough fix. And from I hear around here its something you just "do" when getting an motor of unknown history.

Every screw is going to shear on the lower gear case. I don't think I could manage that too
 

cfauvel

Chief Petty Officer
Joined
Aug 16, 2005
Messages
645
That is aluminum oxide---the same stuff sandpaper is made of. Nothing that I know of will dissolve it. I even asked my brother, who is a chemist and a rocket scientist (really). I told him that if he could come up with something, I'll market it and share the wealth. Nothing yet.


:-(

bummer
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Run this motor and look for a good parts motor.-----In some areas these are not popular and dealers do not fix or hoard the parts.------Found one in a scrap bin ( fire damage , good lower unit ) and one lower unit in good shape at the same yard.----Just time invested on my part.
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
So I'm in the process of finishing up what I think will work. I've got a carbide tip for my dremel and I'm going to grind the screw out of the top plate and drill and rethread the bottom half after I drill out the rest of the screw. I'll give an update if it works out. I'm curious what the impeller looks like since it doesn't seem like anyone has ever gotten as far as I have in this thing
 

Globejs86

Seaman Apprentice
Thread starter
Joined
Jul 6, 2017
Messages
43
No Title

Thankfully I didn't have to grind down the entire screw before being able to pry the top cover off. It left me a nub to grab with my vice grips and back out what was left.

I was really hoping the impeller would be reduced to crumbled rubber, but it wasn't. It really didn't look that bad. A bit worn on the side that rubs around the perimeter, but still flexible and no major cracks.

The new one is here tomorrow so it's getting replaced.

There seems to be a plate below the thin stainless steel plate that has a gasket below it. A small bit of oil has seeped out from under this plate and I'm wondering if the gasket is something I should replace or if it will seal back up once the screws are tightened down again.
 

Attachments

  • photo271181.jpg
    photo271181.jpg
    89.5 KB · Views: 0
  • photo271182.jpg
    photo271182.jpg
    97 KB · Views: 0
  • photo271183.jpg
    photo271183.jpg
    75.3 KB · Views: 0
Top