Rev Limiter

wayneo18

Recruit
Thread starter
Joined
Jul 18, 2016
Messages
5
I have a 1998 Evinrude 70 HP with 180+ hrs. Yes the HRS are correct. I've had it for about 7 years with no problems. I took it to the local shop because the rev limiter intermittingly would come on while I was cruising in gear around 2700 RPM. Now after $600 at the local repair shop I still have the same problem. The local shop said it was overheating. So the water pump, thermostat and thermostat sensor have been changed also had a saltwater engine flush. Still not fixed.So I decided to try and fix it myself. I'm going to start with the neutral safety switch. I did ohm it out ,pushed it in and had continuity, released it and had none. It seems to be fine but I'm not confinced since it is a itermitent problem. Any thouhgts?
 

Chris1956

Honorary Supreme Mariner
Joined
Mar 25, 2004
Messages
29,332
Neutral safety switch keeps the motor from starting in gear. It interrupts the starter circuit, not the ign circuit.

I know my '98 Johnny V6 has a rev limiter (6200 RPM), but it is in the powerpack.

Have you checked to make sure all spark plugs are firing? They all need to have a healthly spark, and they should all look the same when removed, ideally they should be light to dark brown.
 

wayneo18

Recruit
Thread starter
Joined
Jul 18, 2016
Messages
5
Yes all the plugs are brand new. I change them every year. The boat runs great ,but when it wants to it hits that 2700 RPM in gear and hits that rev limiter.
 

gm280

Supreme Mariner
Joined
Jun 26, 2011
Messages
14,605
:welcome: wayneo18 to iboats. Glad you joined us....

Are you sure it is the rev limiter that is causing your 2700RPM issues? Could be some wires that are shorting out against the engine case and causing the ignition to shut off. So how are you verifying it is the Rev Limiter circuit as your problem? :noidea:
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Its the s.l.o.w. system causing this. Do you have a warning horn soud? Do you have system check light illuminated? Is the VRO still connected?
 
Last edited:

wayneo18

Recruit
Thread starter
Joined
Jul 18, 2016
Messages
5
The motor does not shut off at all it just stays at 2700 RPM , up and down. The only reason why I think its the rev limiter is when I'm at home running the motor on the ear muffs in neutral and I advance the throttle to 2700 RPM, the rev limiter kicks in, and it does the same thing intermittingly when I'm on the water in gear. I guess you can call it the s.l.o.w system causing this, I've heard that terminology before? I do not have any warning lights or horns on this unit. I don't know what the VRO is.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
You have either a bad sensor or a bad pack. Start by posting model number. We can then help you with diagnoseing
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Since you are trying to diagnose an ignition problem-probably with the factory "SLOW" system, you may want to refer to the factory service manual. You will find a lot of valuable info regarding your problem. Check out this website: OUTBOARDBOOKS.COM. The SLOW system is designed to prevent overheat damage to the powerhead, by limiting engine rpm's to 2500 when the engine overheats to 203 degrees and above. The "slow" mode cancels then the powerhead temps get back down below 162 degrees.
 

wayneo18

Recruit
Thread starter
Joined
Jul 18, 2016
Messages
5
emdsapmgr, I think your on the right track. As stated in my earlier post the local tech kept pulling overheat codes on the computer and that's why the water pump thermostat and sensor have all been changed. I thought that wasn't an issue anymore. If it is the SLOW system kicking in ,how about a different degree thermostat or even pulling it out all together?
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Post model number as a 98 70hp don't have a computer to pull codes.....
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
I am not a fan of running any outboard without a stat. How about going another direction? You may be better off pulling the exhaust manifold and the head cover off the engine. You may have some blockage inside the cooling system. I'd start there first.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
He may have a ficht. Didnt those start in 97 or 98. If so welcome to the ecm/emm blues. There is an outfit in GA. That can repair some of them. Faztbullet emdsapmgr prolly knows the name. I have it written down somewhere but cant find it.

Either way, a knowledgeable tech with the proper software and yools can tell you if its the emm. Basically you go through everything else and the flow chart tells you replace the emm. Problem is they are NLA.
 

wayneo18

Recruit
Thread starter
Joined
Jul 18, 2016
Messages
5
I had the technician check the ECM when I had it in the shop. He had a spare and plugged it in and still had the problem. I'm trying to avoid pulling the head and manifold off if possible.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
I know Johnson dropped the 4 stroke line in 99 and it was a Suzuki and Evinrude went to DI in 2000-01. I know the 75hp was a V4 DI but the 98-01 70hp is a 4 stroke and none of my manuals show a 70hp DI...
 

82rude

Rear Admiral
Joined
May 8, 2012
Messages
4,082
Ask your mech if your motor has a shift position sensor.If you have a suzarude that might be your problem.In the forum I was reading about df Suzuki issues that came up as a limiter to 2500rpm and was fixed by spray lube.Not to be confused with neutral switch .
 
Top