Replacing Powerhead on Johnso 115 1995

whejdak

Cadet
Thread starter
Joined
Oct 29, 2013
Messages
14
How difficult is it to replace the powerhead on the Johnson 115 1995 outboard. I know it's a vague question. I have been told and I saw a cylinder hear pretty messed up. I'm having difficulty getting anyone to work on it. All say machine time is the problem. If I buy a rebuilt power head and put it on, am i just asking for problems or is this a fairly simple job, just removing all components from old block to new block?

Thanks
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Are you working on a 1995 crossflow or a 1995 looper engine? Two different engines.
 
Last edited:

out 2 launch

Petty Officer 3rd Class
Joined
Dec 11, 2008
Messages
77
I wouldn't be too concerned, at this point, what engine it is. A rebuilt power head usually requires that all the components of the old block be installed on the rebuilt block. So the first question that must be answered is what caused the problem in the first place. For example: Lets say that the bad cylinder was a result of a lean mixture. If the problem is a restricted main jet and isn't corrected then chances are it will happen again.
 

whejdak

Cadet
Thread starter
Joined
Oct 29, 2013
Messages
14
J115TLEOR I've looked up the codes for this model but it says nothing about what we are looking for ?
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
It's a 90 degree crossflow engine. It's a 2-3 hour job to swap the powerhead. The block has a lifting eye right behind the flywheel, so any engine lifter can pick it up. Swapping the components to the new block is not difficult. Two things you'll have to read up on: 1. sync and link the carbs to the spark advance. 2. setting the max timing on the new engine. You need to know what you are doing on both issues, so make sure you are working from a factory service manual. That manual will also give you important information like the flywheel torque specs and greasing the crank splines.
 

whejdak

Cadet
Thread starter
Joined
Oct 29, 2013
Messages
14
Wow, that doesn't sound bad at all.
90 degree? 90 degree from what? Does that mean the cylinders are in a v-shape with 90 degrees between them?? Or what! How did you know it was crossflow and 90 degrees. I'm curious.

Thanks
 

whejdak

Cadet
Thread starter
Joined
Oct 29, 2013
Messages
14
Ok I get it. I went out and measured piston arrangement. Mine is 90 degrees. Not 60 . So it must be a 90 degree cross flow.
I don't see any lifting eyes.
It looks like I'd have to use the fly wheel bolt hole.
I'm assuming that when replacing components that first off is last in. Looks like lots of things to take off. Some will be easier then others.
I am surprised no one has made a DVD yet to do this operation.

I had a John Deere tractor and I want to rebuild the engine. I bought a DVD for that purpose and it was a piece of cake.

I've searched high and low on the internet and have seen lots of conflicting information about doing this.

$2700 plus is a lot to put into it when you aren't sure of what exactly you are doing.
 
Joined
Feb 17, 2012
Messages
2,906
First thing I would do is take the head off the side with the bad piston and post some pictures of the damage. It may be repairable (still a lot of work) but it will show what kind of damage was done. The last thing you want to do is rebuild the engine and put a part on there that caused the problem in the first place. I tend to think of the engines as 4 small engines all stacked together so if you killed one piston then you need to look at why one engine was failed and the other did not.
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Repairing your current failed engine is a lot tougher than just bolting a new powerhead on. The factory parts diagram shows the lifting eye on that engine. If not, I'd use a 3-legged wheel puller on the flywheel to lift it with a chain or heavy strap. A factory service manual should indicate how to decode the model number of your engine. For instance the letters "EO" in the model number indicate 95, the year of manufacture. I agree with glenn. A must to know the reason for the failure of the old block-prior to starting up the new one.
 
Top