Red RTV Gasket maker for Johnson 15

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I was here a while back asking about my OMC 15 that I was trying to rebuild and the rod caps and bearing were not matched up because I got a new crank and pistons for it and those parts were not matched up plus the guy that sold them to me marked the bearings 1 and 2 and I think of 1 as the piston in the top part of the engine and maybe many think of that as #2. Anyway I gave up on the motor as it was too tight to turn over and then 2 weeks later got the bug to try it again. I tried every way on earth to match those parts and finally got it assembled to where the crank turns lightly and I hope it does not destroy it's self after I start it. lol Anyway my question is I used RTV gasket maker for putting the crankcase halves together. It is not the clear type but that old non-see through type that has been around for years. After applying a fairly thin bead I can look in the cylinder from the intake area when I turn the crank and see that some of the RTV is on the inside walls of the cylinder as it squeezed out from the pressure of bolting the crankcase halves together.. Will this be a problem as it will probably get washed off the walls by heat and gas.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
I'll freely admit I'm VERY new to outboards, and any car experience I had was YEARS ago..
So I want to ask as a learning experience..

Every outboard crankcase I've seen (in diagrams, and the 2 I own) have the halves being below the cylinders.
There is the cylinders (top/aft half) and the bottom to cover the crankshaft (bottom/fore half as mounted on a boat)

I guess I have to wonder.. How is there any way for sealer to get into the cylinders so it's seen on the cylinder walls if it was only applied to the crankcase halves? That doesn't seem possible. Pistons (case side, not combustion side), bottom of rings, rods and crankshaft would be where it MIGHT show up in my mind..

How the heck would it get into the cylinder wall proper? Or do you mean the crankcase side of the walls that would be crankcase side, below the rings?

Initial thought would be way too much sealer used, yet you did say a fairly thin bead..
But again... I am very very new to outboards.

I'm NOT trying to be a wiseguy.. I really want to understand this.. It doesn't make sense to me as described...

Thanks for indulging me... :)

Edit: I know on a 2 stroke, the intake side is the crankcase side, so not the combustion chamber of the cylinder. Just trying to reconcile your description of RTV in the cylinder..
 
Last edited:

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
STOP !!------You need to use Loctite 518 or the factory " gel seal " for the crankcase joint.----Very important to use the right stuff.----Never use RTV for that application !
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Well, it is too late now raceone...my question is what can I expect to happen? Engine seize up, blow up ?

Sorry jb, my nomenclature needs refining. Yes, it was the crankcase walls and you are right as it would be quite impossible for the stuff to get on the piston walls. An engine type where that was possible would be interesting though. Instead of tearing the whole engine down to replace rings, maybe adding something like JB weld solution to the cylinder walls might bring lost compression back to life?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Good luck with this motor.-----The correct sealer does not have " fillers " and most if not all squeezes out.----This means you get proper metal to metal fit.---This means you will get proper " clamp up " of the bearings !---Chance of loose bearings in the block is not good.-----You say you are very familiar with motors but lack of knowledge has been demonstrated a number of times.----Sorry, I had to say it.
 
Last edited:

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
OP...your choice....but if it were me, I would definitely pull it apart again and fix it RIGHT.
 

thumbnut

Petty Officer 3rd Class
Joined
Sep 29, 2006
Messages
98
I was here a while back asking about my OMC 15 that I was trying to rebuild and the rod caps and bearing were not matched up because I got a new crank and pistons for it and those parts were not matched up plus the guy that sold them to me marked the bearings 1 and 2 and I think of 1 as the piston in the top part of the engine and maybe many think of that as #2. Anyway I gave up on the motor as it was too tight to turn over and then 2 weeks later got the bug to try it again. I tried every way on earth to match those parts and finally got it assembled to where the crank turns lightly and I hope it does not destroy it's self after I start it. lol Anyway my question is I used RTV gasket maker for putting the crankcase halves together. It is not the clear type but that old non-see through type that has been around for years. After applying a fairly thin bead I can look in the cylinder from the intake area when I turn the crank and see that some of the RTV is on the inside walls of the cylinder as it squeezed out from the pressure of bolting the crankcase halves together.. Will this be a problem as it will probably get washed off the walls by heat and gas.

http://www.apba.org/sites/all/files/documents/2018 JUNIOR rules_0.pdf

Take it apart..double check and reassemble using 518 and the page 10 specs. That outta keep ya busy..
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
raceone...never said I know everything about motors...if I did I would have no reason to be here. I mentioned that it has been many years since I rebuilt a small engine. I have access to a number of the 15's so no real need to rebuild, just did not want to waste the rest of the motor as it is in good condition. Anyway guys, I have spent enough time on this engine and will see what happens. Maybe it will prove some wrong, who knows? I have a hunch it will run and keep running as I have seen these 15's so totally abused and neglected, logic and reason sez they should not be running but do. I think some it the stuff will get blown out the exhaust and some stay in the crankcase where it may interfere with lubrication or vacuum. I'm willing to risk it as time is more than money today. One reason few are rebuilding engines.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You have been very reluctant in following good advice on this motor.-----But good luck with it anyway.----You say you come on here to learn and get guidance. ----But then go off on your own !!!
 

Cadillac-ack-ack

Petty Officer 2nd Class
Joined
Dec 1, 2017
Messages
104
Maybe it will prove some wrong, who knows? I have a hunch it will run and keep running as I have seen these 15's so totally abused and neglected, logic and reason sez they should not be running but do.
Your motor may run just fine, or... At first glance RTV seems like it would be of the perfect consistency to use between zero tolerance machined parts such as engine cases. The problem is, it cures in ambient temperature with exposure to moisture in the air meaning as soon as it escapes from the tube it starts to set-up. The thinner you try to apply it, the faster it sets up, the more you fart around by attempting to spread it consistently, the faster it sets up. This means when you bolt the parts together you end up with the very material, the RTV , you used to seal the cases, actually holding the two parts off a wee bit. The result, in the example of your 15 HP is the crank is not clamped as tightly as it should be. It may be tight enough, or not.

Locktite 518 is what's called "anaerobic" meaning it cures in the absence of air. It's initial consistency is similar to RTV, a bit thinner and stickier though. You can spread it evenly with a small acid brush and it won't ball up like RTV will. Also it will not start to cure until the parts are assembled meaning you will get accurate metal- to- metal contact between the two case halves. The purpose of any sealer here is not as a gasket substitute, but to seal any microscopic pits and scratches left from initial machining of the two halves. - Pete
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
RTV is not resistant to gasoline. It will deteriorate over time, and you will likely develop crankcase air leaks.
The motor will probably run OK for a while, but will fail in the future, and you will be back here wondering why if just doesn't run right, or why there is oil leaking out the side of the engine....you get my point.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Caddy, good interesting and very informative post, the kind I was looking for. Seems you have not been here long with 64 posts but yet you give the "right stuff" without any agenda like some of the old salts., like how far and strong a spark will jump with a certain kind of tested that I don't use..... ad nausea.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Oh, well, bee, my 4 strokes leak out the side of the engine all the time...lol...thanks for the info, you are probably right!
 

thumbnut

Petty Officer 3rd Class
Joined
Sep 29, 2006
Messages
98
Caddy, good interesting and very informative post, the kind I was looking for. Seems you have not been here long with 64 posts but yet you give the "right stuff" without any agenda like some of the old salts., like how far and strong a spark will jump with a certain kind of tested that I don't use..... ad nausea.

Next time you are in an auto store or walmart or some place and buy for $3 and auto plug with the longest insulator. Break off the ground electrode and ya got a tester. Now ya have one.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
It appears that 123 thinks that some proper spark / ignition testing is a waste of his time.----He has a better way !.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
He will be back Racer...after a couple of lean sneezes the silicon will vacant the crankcase halfs
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
But … would still like to hear if and how the seals fail — likewise, if a year from now the motor is still in use and running fine.
 

thumbnut

Petty Officer 3rd Class
Joined
Sep 29, 2006
Messages
98
...just so ya don't feel bad 123...sometime around 1983 or so I got a 440 stand up jetski that needed attention. I talked my dad into buying a large toothpaste tube size amount of loctite 518 through the family plumbing business. . It was 40 bucks in 1983. I put some on a piece of paper to let it "dry" to see what the finished product was like, which it never did. So I did the logical thing and threw it out...:(.

Out came the tube of silicone sealer for the case half's. Was so proud of the porting I did and had bought a pipe for it and some other stuff for it. The silicone lasted about 10 minutes. Sold the ski to my friend with full disclosure. It actually ran for the summer with fuel spraying out from the cases.

Couple of years later I learned about anaerobic sealers and how they worked. Its okay to make mistakes as long as ya only make the same mistake once.
 
Top