Rebuilding carb right now and have a question.

JamesCoste

Chief Petty Officer
Thread starter
Joined
Jun 15, 2003
Messages
595
I'm rebuilding my 50 HP Johnson's carbs today since the motor runs great one day, funny the next, after sitting up for 4 years without running.<br /><br />Might as well eliminate junk in the carbs.<br /><br />I've got the carbs removed and am working on the first one. I've removed the float and am the step where it says "remove and discard all gaskets, O-rings or sealing washers in the carburetor body casting".<br /><br />I'm to the point where the parts I have remaining in my rebuild kit include 4 aluminum(?) metal discs that are slightly beveled on one side. I can also see where the carb housing has 4 similar sized discs on the housing that are now flattened.<br /><br />1) How do I remove the old ones?<br />2) How do I install the new ones?<br />3) Is this a crucial step in a rebuild?<br /><br />I'm using a Clymer manual. I appreciate the help.
 

nitsuj

Chief Petty Officer
Joined
Jul 22, 2003
Messages
483
Re: Rebuilding carb right now and have a question.

Well, again, I can only answer from motorcycle experience, but those plugs usually cover something the factory didn't want you to mess with. Usually on a bike it's the pilot screw, which is factory set to pass emissions. Not sure whats under it on your carb. To remove them, I've always SLOWLY drilled a small hole through, being careful to not go through and hit whats under them. Then, I start a self tapping sheet metal screw into the hole grip it with either pliers or a slide hammer and coax the plug out. Hope this isn't too far off when applied to outboard motors.
 

OldJohnson60

Cadet
Joined
Jun 16, 2003
Messages
21
Re: Rebuilding carb right now and have a question.

I rebuilt the carbs on my 65 yesterday, I also got the plugs in my kits and My manual says to only replace them if they are leaking, mine werent so I left them in. If yours are you can do the drill and self-tap screw thing just be careful.
 

JamesCoste

Chief Petty Officer
Thread starter
Joined
Jun 15, 2003
Messages
595
Re: Rebuilding carb right now and have a question.

Thanks guys.<br /><br />I'm not going to fool with them. I was pleased to see some "gunk" in one of the bowls of the carbs which was probably breaking loose and clogging up some jets from time to time.<br /><br />They are clean as a whistle now and should be back on this afternoon. I'm doing this slow and carefully. I don't want to mess this up. :)
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Re: Rebuilding carb right now and have a question.

One of the pros might lend a hand here -- But based on my amateur experience, the only sure-fire way to clean out the low speed oriface is to to take out the disc and run a thin wire through the openings under the disc. A guitar string works well. You can also shoot compressed air through (or just blow through the opening for the slow speed needle at the front of the carburetor) without removing the disc to determine whether there is a blockage -- and perhaps to remove one. The method discussed earlier for removing the disc is the same that I use. The discs from the kit should fit properly (can lightly tap them into place). I have sometimes sealed the disc with a little epoxy when I thought maybe it wasn't completely sealed.
 

heyttown

Chief Petty Officer
Joined
Aug 3, 2003
Messages
537
Re: Rebuilding carb right now and have a question.

Just as a lessoned learned tip.......... I just rebuilt my carb on my 28 and Clymers said for my model carb to adjust the needle valve 2 1/2 turns counterclockwise......... I did that and had nothing but problems, I ended up having a mechanic, slide me between the projects he was working on, 1 1/2 turns and we were in business, he says Clymers unfortunatly is for a broad range of motors, he showd me the mechanics manual on my specific motor and it states 1 1/2 turns...............................Point being Clymers can get ya through it but it may not be exactly right!...... Good luck.
 
Top