Power Surge

Formula 24

Recruit
Thread starter
Joined
Nov 17, 2010
Messages
2
I want to protect my new electronics from the possiblity of a power surge therefore I want to install a 12V surge protecter.
Has any one done this and if so what unit did you use and how was it wired in? This will be going on a 1979 Forumla 233 which has twin
Model 470 Mercruisers.
Thank you for the help.
 

TerryMSU

Senior Chief Petty Officer
Joined
Jul 31, 2007
Messages
743
Re: Power Surge

Actually one of the worst surges that an automotive system sees is called "load dump". Load dump occurs when the battery is suddenly disconnected while the alternator is running. (This is potentially something that could happen in a boat.) An unclamped load dump can be as high as 100 volts or more. Many (but not all) automotive OEMs will clamp load dump to some lower voltage (such as 40 volts or so.) In the automotive supplier market place, we must design systems to handle load dump as well as some other nasty transients (including reverse battery and double battery conditions.) I am not sure if marine electrical systems are capable of generating that sort of abuse or will tolerate that sort of abuse.

TerryMSU
 

kahuna123

Senior Chief Petty Officer
Joined
Jun 2, 2011
Messages
703
Re: Power Surge

Cabo solved that problem by feeding BOTH sides to the main 12v buss. With a large diode in both lines so alts did not "see" each other. Works great and unless you start both motors at the same time pretty much eliminates a surge. I did that in my Luhrs after watching a $2,500 plotter reset after starting the port motor.
You can by them online for 7 bucks or so. Or go to a alternator shop and they can set you up. Parallel two if you can't get enough amperage.

But someone here will probably tell you go but an isolator for $150 bucks. By the way a 10 year old used 35 Cabo sells for $200,000.
 

Formula 24

Recruit
Thread starter
Joined
Nov 17, 2010
Messages
2
Re: Power Surge

Thanks to every one for the replies. kahuna 123 that sounds like what I am hunting for. How would I wire that set up in?
 

kahuna123

Senior Chief Petty Officer
Joined
Jun 2, 2011
Messages
703
Re: Power Surge

Normally in twin engine made for consumer boats there are two separate 12 systems. Port and Starboard. Whether each "system" has dual batteries or one. Each side having a battery switch either turning off one battery, paralleling two. From that switch should be a fairly substantial feed to the breaker panel, buss under the dash, whatever. In the case of larger boats the 12v breaker panel is usually split in two with each side taking half the load. Cabo there is no split. There is only once buss that feeds the 12 volt systems. The port and starboard 12 volt feeds from EACH battery switch are connected to the 12v breaker feed. There is a high amp diode in line on each feed wire that does not allow the current to run backwards in case their is a voltage potential difference between the two. So when starting one motor the OTHER side carries the load when the voltage drop occurs and vice versa.

This has absolutely nothing to do with how the batteries are charged from the alternators. How many batteries, how many amp alts, whatever. This is only how from the battery switch FEED to the 12volt buss. Please don't confuse the two.

Bubba does that make more sense now??
 

kahuna123

Senior Chief Petty Officer
Joined
Jun 2, 2011
Messages
703
Re: Power Surge

Exactly, so when one engine is being cranked the other is either already running or is not being cranked over.. Therefore it can now carry the voltage to the buss so there is no voltage drop. The reason for the diode is so that neither side tries to feed the other side via the 12v buss in case of low voltage on either side. Also its never a good idea to have two alternators in the same circuit path.
There is nothing worse than watching 5 grand of electronics go blank and reboot.
This way in case of a major problem with one system the other can still run everything and get you home.
 
Top