OMC 15 rebuild

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
It's also possible, at this point, that if you've torqued the rod bolts with the rod caps misaligned or simply on the wrong rods, that you've bent the rod caps or rods. Torquing the rod bolts with the caps out of kilter will make things try to straighten themselves out, which will result in an out of round rod cap. At this point you may need to replace the rods. A small inside mic or caliper may be able to tell you if they're out of round.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Stop-----You need to verify that the rod caps are both part of the rods you are using.------Trial fit them out of the block.----And this should be a simple visual inspection of these joints.-----They were " fractured " at the factory .----Rods only fit the rod they were broken from. !!!!!
 

Scott Danforth

Grumpy Vintage Moderator still playing with boats
Staff member
Joined
Jul 23, 2011
Messages
53,417
thatone123 notice a trend here. everyone is telling you to stop, inspect and measure.
 

heypawpaw

Petty Officer 2nd Class
Joined
Dec 12, 2016
Messages
111
In a previous post you said your measuring skills are not mastered. I know the feeling and suggest you do as I would at this point: Take engine block, crank, pistons, rods, caps, and rings to a machine shop explain situation with rods and caps and let them measure and fit everything. Not assembling to proper specifications and running engine could destroy it.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Thanks all for the good comments. I think you are all right. I have switched, moved and got new con rod bolts all to no avail. Now I know why I stayed away from attempts at rebuilding. I have another of these motors available and will put it in this chassis if necessary. Frustrated to say the least. I will try a little more. The video on u-tube "Small girl rebuilds outboard" OMC 9.9/15 makes it look soooo easy!
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Does anyone think buying 2 new sets of con rod bearings might work out? I guess I hate to give up...but might.
 

Scott Danforth

Grumpy Vintage Moderator still playing with boats
Staff member
Joined
Jul 23, 2011
Messages
53,417
I would mic your crank, have it turned if needed, then buy two brand new con-rods with new bearings for the proper crank journal size.

however until you measure what you have to know what you need, dont waste any more of your money.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
???---You still have not confirmed whether the caps that you have belong to the rods that you bought.-----It is as easy as 123 to check that out.----Buying new bearings will NOT HELP here.----You can not buy different size bearings either !-----New rods are grossly expensive.----A donor motors are like $ 50 in my area.
 

Cadillac-ack-ack

Petty Officer 2nd Class
Joined
Dec 1, 2017
Messages
104
I lost track of just how many times you have re-installed the caps and rods only to find there apparently is still severe binding. Rods and caps are machined in one piece, machined perfectly then 'fractured' or 'broken', thus making up the rod and cap that needs to be bolted together to become one piece again. The purpose of this is to assure the bolted together assembly is precisely round so all the little needle bearings can spin around on the crank without getting hitched on the joint from the two bolted together parts. The 'fracture' is not a machined surface. The result is both parts have microscopic peaks and pits that should mesh exactly when bolted together. It's like a try tree branch that you break over your knee. You can put the two pieces back together and barely feel the break, or you can jam them back together any which way but you'll easily see the joint because they don't fit. If you had actually torqued the rod caps right up to specs a few times, and indeed had mismatched the parts, I'd be concerned the "peaks and pits" would now be damaged so that even when the correct parts are paired, they would not seamlessly fit. At this point, if it were my motor I'd take the pistons out again and correctly pair the parts. Keeping in mind both rods and caps have indexing marks of some sort (my motor uses a raised '***') that at least show which way round the caps go, there is really only one guess needed before you know what goes where. I'd bolt them together on the bench and feel the inside for the parting line. There must be none felt. If you feel a line, you will need replacement rods/caps. -Pete
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
The video was interesting! Cad, Yes, you are right...I think my mistake was over tightening the con rod bolts and probably screwed up the various surfaces. No one mentions anywhere if it is ok to try to turn the crank over without the bottom of the crankcase which is what I was doing. Do you need to bolt the lower crankcase on everytime you tighten the bolts to see if the crank and pistons will turn easy? Anyway at least some learned a few things here. I have a few of these engines that I can swap for this one. Just wanted to see how this went. Learned a lot!!!
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You can turn the crank after the rod bolts are torqued to about 60 inch lbs.-----Not a problem.---You have to make sure the dowel for the center bearing is seated in the hole.----Then you install the cover.
 
Top