old Johnson 140hp v4...

popol

Recruit
Thread starter
Joined
Apr 6, 2017
Messages
5
Hello everyone.

My name is Paul and i'm from Ghent, Belgium.
24 years old and i have been doing watersports all my life.
3 years ago i found a old small motor boat and a broken engine somewhere else.
During the winter period i was able to 'restore' both. Since then i have spend every good summer day on the water skiing.
(i will try to upload some pictures of this. )

A couple of weeks ago i was able to buy yet another project.
A Pirhana miura. with a Johnson 140v4 .

The boat is in 'good' condition. exept for some cracks at the motor mount :facepalm:
the engine however is a different story....

The guy who i bought it from has had the boat for 3 years.
In those 3 years he tried 4 different mechanics.
None of them where able to fix it...
I hope i can..

so for my question now.
I want to be able to buy parts, and look at the right manual.
but there is no way to identify the engine.
the identification (on the side) is gone..
the only numbers i have are those on the round alu.disc on top of the engine (391226 RPH)
the numbers on the CDI (CD4 582125 M9 18)
And a number on the air intake 322985.
i can get the numbers on the piston and exhaust manifold if this could help.

I was hoping someone here could help me out..
Since the offical dealer could only tell me its between 1980-1985.
But when i look those numbers up i find beween 1978 and 1989.
(depending on what number)





I'm brand new to all of this. I have read a lot of forums in the past but never made my own account.
I'm hoping this is the right way to get response on my questions. If not please show me how it's done.

Thank you.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
RPH indicates a rebuilt powerhead I believe.--------If paint is original post pictures of the motor and cowling / cover.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Yep, the replacement powerhead kills any chance of identifying it by serial number. Best place to start is with some pictures.
 

popol

Recruit
Thread starter
Joined
Apr 6, 2017
Messages
5
there.
Hope this gives you enough information.
If not, please tell me what part you would like to se in more detail.


thank you.

ps: please don't look at my spelling to much. I try my best.
 

Michawilden

Petty Officer 2nd Class
Joined
Apr 4, 2015
Messages
153
Hey Paul. My guess is end 70's early 80's. Such an exhaust cover (bubble back) changed later on, on the 140 hp models ( if it is truely an 140 hp and not just the cover). Parts as coils and powerpacks have been used on several years so that won't pinpoint the exact year.

More important, what are the problems with the motor? (apart from that messy wiring)

p.s. Leuk om te zien trouwens dat er ook anderen uit de buurt op het forum zitten
 

popol

Recruit
Thread starter
Joined
Apr 6, 2017
Messages
5
hey,

thx for the information.

so i should be able to order relays, coils ,... on a 140hp from around 1980.

is it correct when i say the model i have will start with : J140TL...
J (johnson)
140 (hp)
TL ( powertrim)

and then there should be 3 more numbers to complete the modelnumber.
for example CRD ?
or is that wrong?


don't know whats wrong yet.
just to be shure i want to start with the cables.

things i do know are :

-tilt works, Trim does not ( and i can't find a way to lower the trim)
-the starter works, but its relay does not
-3 cilinder heads are clean and 1 is totaly black. does this mean there is a leak?
-4 bolts already broke off in the process :facepalm:
- the coolant channels are full with junk. even TEC7....

i'll post some more pictures later today.

All comments are much appreciated.

thanks.
 

Michawilden

Petty Officer 2nd Class
Joined
Apr 4, 2015
Messages
153
A black cylinder head can be caused by to much gas. Might be that the low speed mixture of this cylinder is off or that the float needle does not shut.
If it was my engine I would start out with a compression test. Test if all cylinders have high compression (arround 110, 120 psi. +- 8 bar) before buying other stuff .
What was the problem with the engine that 3 other could not fix? Or did they install a new powerhead and naver got to installing the electrics?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Compression test is first thing to be done.----Stripes on cowling ( if original scheme ) put it in the 83 / 84 model year.-----What is the nature of the problem that 4 mechanics could not fix ??
 
Last edited:

popol

Recruit
Thread starter
Joined
Apr 6, 2017
Messages
5
thx for the advice.
I think the problem will just be electrical.

The guy who i bought it from told me it would start at idle but does not go above 1500rp

i did not have the chance of starting the engine, since the reley of the starter is broken....
so there is was no way of testing compression..

can i heat up the screws that broke of?
I'm afraid of the aluminum around it.

i tried with a special screwdriver (when you hit it, it turns a little)
i tried welding a nut on it. and it still broke off.

what other tricks do you guys have for this?
 

Michawilden

Petty Officer 2nd Class
Joined
Apr 4, 2015
Messages
153
If they broke when removing they will not be coming out with a counter rotating tap ( I don't know the english word). They will be seized in the powerhead. My solution will be to drill them out and placing a helicoil. If you heat up the aluminum you will have to do it evenly and gradually but I think that the studs still won't come out easily.
To late for it now but if you do not have a problem initially do not open it up.
With such a problem I would first check compression, then spark and if that all checks out, the carbs.
 
Top