Newbie to Electrical wiring - would like some assistance :)

Master2k

Recruit
Thread starter
Joined
Jun 9, 2011
Messages
2
I am helping a friend re-do the wiring to his boat and have managed to weed out the wiring that was no longer used - MAJOR clean up done :eek:

First of all - please accept my appologies if I don't know the actual boating terms - I'm just helping here ;)

My question is the following - I want to install a new fuse box with another battery from the back of the boat in order to accomplish the following:

Lighting
I would like to set up the lighting from the new fuse box and new battery to the control panel that would have an on/off flip switch. I know how to connect the wiring and what fuses to use and what gauge wiring to use - but have NO CLUE how to wire from the battery to the fuse box and from the fuse box to the switch then to the lights :(

If anyone would be able to assist me with a diagram (simplified) I would be VERY grateful :)

Kind regards

Gordon
 

sw33ttooth

Chief Petty Officer
Joined
Apr 24, 2011
Messages
498
Re: Newbie to Electrical wiring - would like some assistance :)

from battery you have the negative and positive,
run your positive into a master switch negative to a ground bust,
run your positive to the fuse pannel,
now run your positive wires from the fuse pannel to the switches,
now take your lights, negative the ground bust and positive to the other end of the switch.

just remember black doesnt ever get switched, does help to have your ground bust mounted near your fuse pannel so your not running wires all over.


hopefully my crudy drawn picture is of some help you can run multiple lights off 1 ground wire but it may need to be a larger gauge wire depending on lights if its LED's then it will probably be good they dont draw much at all. but each light should be on its own switch
 

Master2k

Recruit
Thread starter
Joined
Jun 9, 2011
Messages
2
Re: Newbie to Electrical wiring - would like some assistance :)

Thanks for the assistance sw33ttooth :)

Just 1 stupid newbie question :p - what is the ground bust??
 

jhebert

Ensign
Joined
Jul 24, 2005
Messages
903
Re: Newbie to Electrical wiring - would like some assistance :)

You may find this article to be useful for you:


Boat Electrical Circuits and Wiring Practices
http://continuouswave.com/whaler/reference/boatWiring.html

I have no idea, either, what was meant by a "ground bust." In DC wiring on a boat there is generally no ground circuit in the power distribution, there is just a positive and a negative. The intent of "ground bust" was probably to refer (incorrectly) to the DC Negative Primary power distribution bus.

On boats with non-metallic hulls it is common for all metallic components of the fuel system to be connected together by bonding conductors, and the bonding conductor terminated in an electrode in contact with the sea. If there is no bonding electrode, it is common to terminate the bonding circuit to the battery negative, which is generally connected to the outboard engine chassis, which is in contact with the sea via its galvanic corrosion anodes.
 

sw33ttooth

Chief Petty Officer
Joined
Apr 24, 2011
Messages
498
Re: Newbie to Electrical wiring - would like some assistance :)

i've heard it referd to as many things, basically its like a fuse pannel with no fuses negative goes into it and then theres [x] ammount of negative terminals to run wires to/from. there might be one on 1 side of your fuse pannel that is only good for negative. sorry i was thinking about my last boat the idiots ran 2 fuse pannels 1 for negative side 1 for positive side now that i think about it, i believe that my four winns has something like this:



that is about the accual size of it from the switches your positive wire runs back to the fuse pannel to the positive side and obiously the negative side the wire from the lights goes straight into it
 

jhebert

Ensign
Joined
Jul 24, 2005
Messages
903
Re: Newbie to Electrical wiring - would like some assistance :)

I suggest you also ignore the diagram above. It shows bad practice. The over-current protection device in the circuit should be placed near to the source of the positive current and before the switch, not after the switch as shown above.
 
Top