New (to me) Johnson v4 90hp - Need some identification help

Parhamm1

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
8
Hi Folks, new to the forum and pretty new to boat ownership. I bought a 1991 Alumacraft Trophy 170 boat I'll be slowly rehabbing over the fall/winter. The boat has a Johnson v4 90hp motor on it, but it has no ID tags anywhere to be found. The boat ran great for an entire week for me up in Canada, but the last day it wouldn't turn over. I threw a new cranking battery in, replaced a ripped spark plug wire (going to do the rest) and I'm going to replace the NGK plugs in it with the factory spec Champions. I did some trolling with it and I think I ended up fouling the plugs by the end of the week.

I did a compression test when I got home and I'm at 110-120 psi across all cylinders, which I believe is good (someone correct me if I'm wrong).

Regardless, I'm hoping for some ID help so I can get some parts. I'm wanting to rebuild the carbs, replace the fuel filter, fuel line and bulb, water pump and lower seals, maybe the thermostats too. I think doing all of these things will put me in pretty good shape. VRO is disconnected too.

What do you guys think? Good list? Anything else I should consider doing while I'm at al?

Attached are some pics of the motor. Let me know if any of you guys can help me ID the vintage and model.
 

Attachments

  • IMG_1100.JPG
    IMG_1100.JPG
    69.6 KB · Views: 0
  • IMG_1098.JPG
    IMG_1098.JPG
    102.1 KB · Views: 0
  • IMG_1125.JPG
    IMG_1125.JPG
    93 KB · Views: 0
  • IMG_1123.JPG
    IMG_1123.JPG
    114.9 KB · Views: 0
Last edited:

Parhamm1

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
8
Oh, I also have an issue where there is a constant alarm when starting up the boat. It's just a constant tone and I have to inch the key back roughly a 1/4 turn to get the noise to stop, but the gauges then shut down. The tone doesn't stop if I don't inch the key counterclockwise.

Based on some reading it sounds like an overheating alarm but the engine ran great for a week, the water stream was strong and cool to the touch. Not really sure what's up there. Maybe a bad connection? Thinking this is why I want to replace the water pump and maybe the thermostats... any other ideas?
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Your pix don't show as photosuckit has killed 3rd party hosting. Just resize your pix to less than 400kB and post directly.

Look for an aluminium disc the size of a loonie on the top of the port cylinder block - it may have model/serial number. Factory put the SN plate on the starboard engine bracket, just below the upper transom bolt hole. If it's a rivet-on tag, it's older than about '85 - they started making plain printed labels with no rivets around 85.
 

Parhamm1

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
8
I think you can click on the pic to view. Or right click and open to view. Works when I try it.

Thanks for the advice. I checked the block and have a quarter size plate with the number R3613312
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
No Title

All I see is the P500 error picture, a screenshot is attached. Probably works for you as it's cached on your machine.

The disc just shows your serial number. Sometimes they also had the model number there, but not sure what years they did that.

We can get closer to your year. Do the carbs have choke butterflies or is there a primer solenoid with hoses to nipples on the top of the carbs? Do the carbs have flat "C" shaped plates on top, raised ridges with lead shot filling holes, or curved and smooth?
 

Attachments

  • photo275020.png
    photo275020.png
    244.9 KB · Views: 0

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
The R on the plug means it is a replacement powerhead.
 

Parhamm1

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
8
No Title
 

Attachments

  • photo275025.JPG
    photo275025.JPG
    69.6 KB · Views: 0
  • photo275026.JPG
    photo275026.JPG
    102.1 KB · Views: 0
  • photo275027.JPG
    photo275027.JPG
    93 KB · Views: 0
  • photo275028.JPG
    photo275028.JPG
    114.9 KB · Views: 0

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
'89/90 by the looks of the decals on the hood. Carb kits are pretty much generic across many years, late '70s right to the end in the mid '90s. All crossflow V-4s after about '77 use the same thermostats too.
 

Parhamm1

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
8
No Title

Great! Thank you much!

Any ideas about the constant alarm? Or am I going down the right path with the work I'm planning?
 

Attachments

  • photo275033.JPG
    photo275033.JPG
    123.8 KB · Views: 0

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Try disconnecting the brown wires from the temperature sensor leads on each head. Pull back the rubber sleeves and twist the knife connectors open. If the alarm continues, it could be something shorted in the harness or a VRO alarm that's shorting.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
(Odd Soundings Of Warning Horn)
(J. Reeves)

Should the warning horn beep constantly when the key is turned to the ON position rather than sounding just a short beep as it should, do the following test.

Remove the TAN wire from the horn. If the constant beeping continues, the horn is faulty, in which case replace it. However, on the other hand, if the beeping stops, something has gone wrong with one of the sensor components at the engine, in which case start disconnecting the TAN wires that are connected to the various components (Heat Sensors, VRO, Vacuum Switch if so equipped, Oil Tank). Disconnecting a unit and having the beeping stop...... you've found the faulty component.

NOTE: The small black plastic horn that has a built in black ground wire...... The TAN wire must be attached to the terminal closest to that black wire. Otherwise weird things will happen.
 
Top