New points and condensers

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
yes sir, rotating 180 degrees from T to B. Its odd that on the bottom side the points will adjust like they are supposed to but on the top its not allowing the points to be adjusted opened or closed it just moves the whole set. And as you stated its the same lobe so it should not be causing that at all.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Swap points and see what happens.----Inspect point sets closely are they the same ?
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
Well I just dont know. The only way to get it to crank up and run is by setting the points way beyond the marks by about a inch and 1/2....... but both chambers are firing and it is running smooth at tank RPM's. I think I will just leave it alone. Thanks for all your help gents.
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
I GOT IT!! I went back and read everything that raceone wrote. took everything back apart cleaned cleaned and cleaned. installed everything as before. I set the points as per the marks and the meter and it wouldnt work. moved everything just past the marks by about 3/4 of and inch and got spark.put it all back together and it fired right up! Its running great. I dont understand why it wont work lined up but getting great spark to both plugs, pulled one at a time and it kept running on each cylinder. idles nice and at tank rpm's in gear it is smooth enough. Can't thank yall enough.
 

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
Yes sir, have to wait till I can get to town and pick one up. I live in the middle of nowhere. Sure do appreciate your advice.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
John, the purpose of the timing fixture is NOT to set set the timing in relation to TDC. The purpose is to make the points break at the precise correct time as the magnets pass the coils. If you did it right, that is happening, no matter what the points gap is.

Do me a favor and set the points according to the timing fixture method, then measure the gap without changing anything except to position it so the points are on highest area of the cam. They should be somewhere in the vicinity of .020" If they are WAY, WAY off, either you are doing it wrong, or you got a defective timing fixture. That never has happened yet, with all the many I've made, but it is possible. I would have had to be drunk when I put it together, and I don't drink. Personally, I suspect you are getting faulty meter readings due to poor test lead connections to the points or armature plate. Or you are letting the armature plate rotate as you adjust the points.

EDIT: I just read your post where you said you got it working. That bothers me. Send the timing fixture back to me for inspection. I'll pay the postage. Or give you a complete refund if that is what you prefer. I still don't drink.
 
Last edited:

John Wasmuth

Seaman Apprentice
Thread starter
Joined
Feb 3, 2012
Messages
32
LOL, Thank you F_R but I am not so sure that it's a faulty fixture. I'm more convinced that it has something to do with the plate. Before I did the points and condensers it was running but would some times miss and upon inspection the old points had most certainly seen better days. Following your video I attempted to set the timing as you did however even using the meter it just couldn't come together. I haven't messed with points since I sold my 68 Rambler back years ago. To me the plate seems like it just isnt right. If you will allow me time to get a timing light and check it all out before we send back the fixture that'd be great. It's a quality built piece of equipment and well worth the money I spent on it. And I am never going to rule out operator error....... When it comes to stuff like this i am most certainly not the sharpest tack in the box. I'll be getting a light in the next couple of days and when I tear it all down again I'll check the gap. I did on the last go round, check the gap against the meter with the paper included with the points and it slid right thru and verified that the meter was correct that there was no continuity. I did not however check it with the .020 feeler gauge.
 
Top