New 5.7 issues with old(new) starter

G

Galvez83

Petty Officer 1st Class
Joined
Oct 31, 2019
Messages
279
Folks i have an issue with a rebuilt 5.7 4 bolt 880 block. Long story short old block which was newly rebuilt less than 10 hrs on it was sent back due to noise. I was given a reman 880 5.7 block. All parts bolted back in but there is an issue with the starter. Starter is new and was bought and used in the previous block. The issue is the starter when activated bumps to the flywheel and retracts. Starter works fine. I see more of a clearance issue. Even when i bolt it to the block 1 of the starter bolts butts up to the flywheel cover not allowing you to bolt it in properly. Now the question is what could be the issue? Engine was previously tbi and was coverted to carb prior to engine removal. Went from 5.7 to 5.7 should be no issues. Any ideas whould be appreciated.
 
Bondo

Bondo

Moderator
Staff member
Joined
Apr 17, 2002
Messages
70,958
Ayuh,..... Chevy starters only come in 2 flavors, straight across bolts or staggered pattern,.....
The flywheel diameter determines which you need,....
 
G

Galvez83

Petty Officer 1st Class
Joined
Oct 31, 2019
Messages
279
Even though it was the same flywheel and same starter used on the motor that was turned in? They both worked fine with one another. They actually played nice, no issues to report.
 
Last edited:
flashback

flashback

Captain
Joined
Jun 28, 2002
Messages
3,963
Maybe, what kind of noise was the first 10 hr engine complaining about..?
 
G

Galvez83

Petty Officer 1st Class
Joined
Oct 31, 2019
Messages
279
flashback said:
Maybe, what kind of noise was the first 10 hr engine complaining about..?
Click to expand...
After a couple of uses it was a whining noise under load. Items discarded was, pulleys, outdrive and bearing. At the end it was determined to be internal from rebuild. Whent with different builder for this engine.
 
D

Donald0039

Chief Petty Officer
Joined
Jun 11, 2022
Messages
402
Both starter bolts the same length?

Something is odd. Could anything be bent?
 
G

Galvez83

Petty Officer 1st Class
Joined
Oct 31, 2019
Messages
279
No, single engine. The good thing is that engine is on test stand for first start. So far as per the flywheel part number its 3853958. Indicates 168 teeth 14 inches wide.
 
jimmbo

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
13,446
Galvez83 said:
Folks i have an issue with a rebuilt 5.7 4 bolt 880 block. Long story short old block which was newly rebuilt less than 10 hrs on it was sent back due to noise. I was given a reman 880 5.7 block. All parts bolted back in but there is an issue with the starter. Starter is new and was bought and used in the previous block. The issue is the starter when activated bumps to the flywheel and retracts. Starter works fine. I see more of a clearance issue. Even when i bolt it to the block 1 of the starter bolts butts up to the flywheel cover not allowing you to bolt it in properly. Now the question is what could be the issue? Engine was previously tbi and was coverted to carb prior to engine removal. Went from 5.7 to 5.7 should be no issues. Any ideas whould be appreciated.
Click to expand...
Just out of Curiosity, where was the Starter bought?
 
Bondo

Bondo

Moderator
Staff member
Joined
Apr 17, 2002
Messages
70,958
Galvez83 said:
No, single engine. The good thing is that engine is on test stand for first start. So far as per the flywheel part number its 3853958. Indicates 168 teeth 14 inches wide.
Click to expand...
Ayuh,..... Then you need a staggered pattern starter,......
 
Lou C

Lou C

Supreme Mariner
Joined
Nov 10, 2002
Messages
12,681
make sure you use the correct length bolts, a lot of these aftermarket starters use slightly different size housings and if the bolts bottom out in the block, the starter will twist under torque and break the bolts, putting you in a world of hurt!
This is an ARCO PMGR starter that I replaced the old Delco direct drive starter with...used ARCO's bolts...spins the engine over faster than any of the old style starters I used....
PMGR vs DD.JPG
 
G

Galvez83

Petty Officer 1st Class
Joined
Oct 31, 2019
Messages
279
jimmbo said:
Was it a USCG certified Marine Starter?
Click to expand...
Yes, black marine certified. This is as weird as weird gets. Same starter, same flywheel that where working perfectly together. The starter engages when power is applied but it hits the front of the flywheel then retracts. The bolts look fine. I did notice that the bolt that is oposite to the engine is butting to close to the flywheel cover. That wasnt and issue before. To the point that you can't fit a socket on the bolt. The only difference in all of this is the block. Old(new) block turned in was 2 bolt main and this is a 4 bolt main.
 
Last edited:
You must log in or register to reply here.
Top