Need wiring help please

MFnAQUAMAN

Recruit
Thread starter
Joined
Aug 30, 2010
Messages
3
1986 grady white / 200 hp GT v6 / two batteries on a switch.
Had it rewired and now the selector switch activates the ignition... like where you used to turn the key one click clockwise and youd get a beep ... it happens now when you turn the slector to battery one or two. So I get on the boat and turn the selector on and BEEP ... turning the key one click right does not beep at all now... wondering if this is frying my electronics ... I know it isnt supposed to be this way . . but if someone knows and says that it wouldnt harm anything then great ... I lost a powerpack .. changed it still only 2900 rpms ..timer base and still getting low rpms , like 4000 and now all cylinders sparking , but weak ( I can pull the boot off and doesnt even really shock me but makes the clicking noise - so about to change the stator ,,, almost 800 in parts already and wondering if having the wiring like that could possibly be a problem ... please help
 

reddogg

Petty Officer 1st Class
Joined
Jun 3, 2011
Messages
379
Re: Need wiring help please

That dosent sound right to me. Check and see what they did with the 12v power wire from the engine. The engine is supposed to be hooked to the batts (actually the switch) in the back with the leads running forward to power your gages, tach, etc.. when the key is turned on. All your other accesories are supposed to be powerd from a fusebox that is supplied with power via a hot and ground cable running forwards from the batts. If it's beep ing when you turn on the batts, it sounds like someone has bypased that 12v power wire from the motor and wired your stuff from the fuse box. I don't know about possible damage, but I know that from the way it sounds, it's not wired correctly right now.

Red
 

MFnAQUAMAN

Recruit
Thread starter
Joined
Aug 30, 2010
Messages
3
Re: Need wiring help please

Thanks red ... I lost a pwer pack timer base and i think a stator too and had read something about low voltage damaging the electrical system if the key switch was incorrectly set up ( not a mechanic:) )

Basically I had the wiring done in March thought I took an early jump on the season cleaning up my wires and ready to hit the water for that early floundering .. when he was finished and I asked him about the selector beeping he said it was fine ( great guy) ... after the first or second run out wouldnt start ... so got a flywheel ( magnets were destroyed) and a power pack ... started right up .. and then after a trip or two would only get 3000 rpms .. turns out I lost the middle cylinder on port side so I got a timer base - now I have spark on all cylinders but they are weak and Im still not breaking 5000 like i used to and my boat tops at 42 or so and im only getting up to 25 30 tops .. I think i now need a stator - I did not meter test the spark ... got all new plugs and wires .030 gap what not .. when i pull a boot barehanded i hear clicking on all 6 but it doesnt really zing me too much i almost feel no shock but they are firing - i think just weak ... so any way everything in the electrical system dying (which now my concern is will it happen to my 900 worth of new stuff) ,,is it just Coincidence? and not because the selector beeping is a sure sign of being wired retarded and shorted all my stuff out , ? ... ok im cool with that :redface::confused: and I know i know carbs too rt ... ( about the RPMs being low ) ok ill have to check that ... any more info will be greatly appreciated
 

MFnAQUAMAN

Recruit
Thread starter
Joined
Aug 30, 2010
Messages
3
Re: Need wiring help please

SOME MORE INFO !?!?!?!?!?!?!?! ANYONE?????
Looking for someone to basically tell me that my cooky wirng could not kill my Powerpack timer base and stator
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Need wiring help please

Not knowing what the shop did with the re-wire what can we do? Here is what the system should look like. The diagram doesn't show the feed to the fuse panel but ALL loads, including the large positive engine battery cable should be connected to the COM terminal on the switch. Only an automatic bilge pump would be hooked directly to the largest battery in the system. There are lots of "creative" ways to incorporate dual battery switches but most of them defeat the flexibility of system.

StandardBatterySwitchWiring.jpg
 
Top