My DC system needs your help!

diverseyrink

Recruit
Thread starter
Joined
May 4, 2008
Messages
3
Hello there. I have an issue with my boats DC system that I need a hand with.

I have a 32' cruiser with twins, 2 crank + 1 house batt, a 2 alt 3 batt isolator, and a Xantrex 40+ charger.

My voltmeters on both side very rarely hit 13 - in idle and even while underway they hover around 10. I hit the blowers, they drop to a hair over 8. When anything else happens - toilet flush, running lights, etc., the radio goes dead for obvious reasons. This is the scenario most of the time, but other times things seem much better.

While at the harbor with the batt charger cranking, the same happens most of the time. This is very frustrating. Hell, even underway with the Genset on giving the charger juice, the head still kills the radio.

I've replaced all 3 batts and the charger. My next stop would be to replace the isolator - as this seems to be common across all scenarios.

Thoughts?

Please advise.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: My DC system needs your help!

At 8 -10 Vdc neither start battery is being charged so don't leave the dock until you get this fixed. As you are finding out, replacing parts is not troubleshooting -- its shotgunning blindfolded hoping you get lucky. Follow the juice. When you lose it, you found the problem. If you have power going into the isolator but not out of it, the isolator is bad. If you have power out of the charger, it's ok. If not -- its not. Bad battery and electrical connections are generally the source of many electrical problems. Don't just look at them, disconnect them, make them shiny clean and tighten securely. That means both ends of a cable.
 

joed

Lieutenant Junior Grade
Joined
Sep 28, 2002
Messages
1,135
Re: My DC system needs your help!

Verify the voltage at the battery. You could have voltage drop issue with too small a cable.
If the battery never get to 13.5 volts even on the charger then there is a problem with the batteries or the charger.
 

diverseyrink

Recruit
Thread starter
Joined
May 4, 2008
Messages
3
Re: My DC system needs your help!

Yes, but I've NEVER had any problem turning over either of the engines.

2 ?s :

1) Does this sound like it could be the isolator? The boat was purchased new 4 seasons ago.

2) As far as cable runs, the batts are mounted against the bulkhead and the bat switches are probably a 8 foot run away...very heavy duty cable - not sure the exact gauge. The switches are both on/off/emergency bridge. The charger and isolator are almost directly above the batts, so the run there is prob around 4 feel with all the looming, etc. And the run from the Alts is probably "standard" - around 5 feet as well.

So first thing to do would be to disconnect everything and grab a toothbursh?

It seems to me as if the batts aren't getting charged after they turn the engine over so when there's a draw, volts drop. But then with the revs at 3 grand, the alts should be putting out enough juice to cover everything so then I point to the isolator in that it's not letting juice into the batts.

Either way, I'm off to the harbor tonight....

Any other advice?
 

bruceb58

Honorary Supreme Mariner
Joined
Mar 5, 2006
Messages
30,834
Re: My DC system needs your help!

You need a multimeter and start measuring voltages at the inputs and outputs of the isolator.
 

diverseyrink

Recruit
Thread starter
Joined
May 4, 2008
Messages
3
Re: My DC system needs your help!

OK. So I purchased a meter, and it looks like the charger, alternators, and isolator all all working as advertised. 13.2 - 14.3 all throughout when the engines are cranking. Thanks Silvertip for the hint!

What I did find out was that at any given time, a reading direct from the house batt reveals 13ish, but that same reading taken at the house panel downstairs is between 2 and 2.5 volts less. The radio's power comes from the house panel - so this explains why I always get shutdown.

So what would cause this voltage loss? The cable goes from the house batt, to the house batt breaker on the transom, the down to the house panel, then gets distro'd from there.

There is almost NO PLAY on these cables, so removing the battery switch panel or the house panel is next to impossible. (Thank you, Rinker)

The easy fix is running a new fused lead from the radio directly to the house batt, but that would be a band-aid; not fixing any problem. BUT, allowing people to flush the head while enjoying XM!

Thoughts?

Thanks.
 

bruceb58

Honorary Supreme Mariner
Joined
Mar 5, 2006
Messages
30,834
Re: My DC system needs your help!

Just keep on measuring voltages at all the intermediate points. Measure with a load so that you will see the drop. With no load, you will always read the battery voltage.
 

tommays

Admiral
Joined
Jul 4, 2004
Messages
6,768
Re: My DC system needs your help!

It sounds like your getting Voltage drop from bad connections at the cables OR time and the marine enviroment has just used them UP

For example it is very common for low quality wire to turn black under the insulation at which point it really does not work well anymore
 
Top