Maybe more than a blown fuse?

baylinerbarry

Recruit
Thread starter
Joined
Jul 19, 2012
Messages
5
I made a big mistake today changing out my batteries. When i hooked everything back up I had made the mistake of running them in a series rather than parallel and blew several fuses. I hooked them up parallel and now I have no cranking power or any dash or inside lights, radio etc. Can someone give me an idea of what could be wrong.
 

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: Maybe more than a blown fuse?

Perhaps if you told us a couple little minor details it would help, like what kind of boat, what model boat, what year of a boat, what kind of motor, we MIGHT be able to help.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: Maybe more than a blown fuse?

And add to what Don said -- just what sort of wiring scheme do you have (what battery does what)? Dual battery switch, ACR, what???????
 

baylinerbarry

Recruit
Thread starter
Joined
Jul 19, 2012
Messages
5
Re: Maybe more than a blown fuse?

It's a 1989 Bayliner Ciera 2455, 350 chevy, cobra outdrive.
Thanks.
 

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: Maybe more than a blown fuse?

Did you turn power on and try to operate the items while you had it in series? I don't see voltage blowing the fuse, amperage is what blows fuses. But it sure wouldn't hurt to check all fuses.

Short of getting your meter out and start following the power and seeing where it stops, I have no ideas for you. Afraid there is no red reset button type circuit breaker causing your problem. Engine power is separate from accessory power on those older Bayliners.
 

dingdongs

Chief Petty Officer
Joined
May 29, 2009
Messages
649
Re: Maybe more than a blown fuse?

90 amp fuse on starter may be a good place to start.will be a main dealer part but were only guessing that you have one, as we've no crystal balls.
 

Don S

Honorary Moderator Emeritus
Joined
Aug 31, 2004
Messages
62,321
Re: Maybe more than a blown fuse?

OMC didn't use a fuse on the starter, only Mercruiser.
 
Joined
Feb 17, 2012
Messages
2,906
Re: Maybe more than a blown fuse?

to be honest i can not see how you accidently hooked in to series unless you thought it was series as that would require changing a few leads. now it would be easy to hook up one battery backwards which if it didnt blow up means that dual switch proberly failed internally more details of the battery set up and some pics would realy help us understand what happened and enable us help. electricity follows rules like amps blow fuses not volts as don pointed out so the more detail you give us the better we can understand how it happened then work out where it should have logically failed
 

baylinerbarry

Recruit
Thread starter
Joined
Jul 19, 2012
Messages
5
Re: Maybe more than a blown fuse?

I have traced the problem to the fuse panel under the dash. I need to have it replaced but don't want to go back with the glass buss fuses. Looking at the original fuse block I am seeing about 15 fuses. Most of what I am finding are 6 & 12. I don't have an owners manual to see what all is on it and am not sure what I need to get.
 

baylinerbarry

Recruit
Thread starter
Joined
Jul 19, 2012
Messages
5
Re: Maybe more than a blown fuse?

And add to what Don said -- just what sort of wiring scheme do you have (what battery does what)? Dual battery switch, ACR, what???????

I have a dual battery switch but usually keep it on both batteries. starter, blower, lights inside and out. depth finders, bildge pumps. I'm sure I'm leaving some things out.
 
Joined
Feb 17, 2012
Messages
2,906
Re: Maybe more than a blown fuse?

honestly im not trying to give you a hard time but how you wired the batterys in series with a dual battery switch in the dual postion realy intrests me. anyway the fuse block you say its the problem as in.....its melted....it has no power?

the fuse block can be bought from any boat store in the more up to date auto style fuses you will need one with the same amount of fuses or more so proberly a 16 fuse block. you will also need a book of wire numbers or masking tape then disconnect batterys and mark each wire with a number so start top left as 1 then top right as 2 and work your way down the wires that go to fuses. make sure they go to a fuse and not the ground bar that may be mounted on the bottom of the original fuse block...(a picture would realy help here) if you have 15 fuses and 25 wires and you do not understand which are which stop now and post a picture. once all the fused wires are marked take a picture then remove all the wires and install new fuse block and plug the wires back on to the new block in the same pattern. i would also surgest installing a main resetable breaker to the wire from the dual switch to the fuse panel. hook up batterys then replace one fuse at a time and test as you go. the fuses are 6a and 12a? or 6/12a?. if they are 6 amp and 12amp then use 5amp and 10 amp in the same places if they are 6/12a then use 5amp fuses. put one fuse in then see what works.....say number one is biege then write that down on the new panel. you might end up with a few that are ????? but thats not a bad thing as if later you discover a problem you have a idea where to start.

its bugging me that i still can not see how messing up the connections on the batterys can take out the fuse block (don or silvertips any ideas on this)
 

baylinerbarry

Recruit
Thread starter
Joined
Jul 19, 2012
Messages
5
Re: Maybe more than a blown fuse?

honestly im not trying to give you a hard time but how you wired the batterys in series with a dual battery switch in the dual postion realy intrests me. anyway the fuse block you say its the problem as in.....its melted....it has no power?

the fuse block can be bought from any boat store in the more up to date auto style fuses you will need one with the same amount of fuses or more so proberly a 16 fuse block. you will also need a book of wire numbers or masking tape then disconnect batterys and mark each wire with a number so start top left as 1 then top right as 2 and work your way down the wires that go to fuses. make sure they go to a fuse and not the ground bar that may be mounted on the bottom of the original fuse block...(a picture would realy help here) if you have 15 fuses and 25 wires and you do not understand which are which stop now and post a picture. once all the fused wires are marked take a picture then remove all the wires and install new fuse block and plug the wires back on to the new block in the same pattern. i would also surgest installing a main resetable breaker to the wire from the dual switch to the fuse panel. hook up batterys then replace one fuse at a time and test as you go. the fuses are 6a and 12a? or 6/12a?. if they are 6 amp and 12amp then use 5amp and 10 amp in the same places if they are 6/12a then use 5amp fuses. put one fuse in then see what works.....say number one is biege then write that down on the new panel. you might end up with a few that are ????? but thats not a bad thing as if later you discover a problem you have a idea where to start.

its bugging me that i still can not see how messing up the connections on the batterys can take out the fuse block (don or silvertips any ideas on this)

Thanks. I will try to get a picture today.
 
Joined
Feb 17, 2012
Messages
2,906
Re: Maybe more than a blown fuse?

looking forward to seeing them. i just dont want to see you replace a fuse block or something else if in fact the battery hook up was not the real problem. sometimes there are more than one problem and the op leaves out a few details then asks why the new part caught fire just like the original did..lol
things like why were you changing the batterys in the first place?
 
Top