Locating fuse, 1969 Johnson 115

smlJohnson115

Cadet
Thread starter
Joined
Sep 5, 2015
Messages
10
Hi,
New here.
I bought this boat at a local benefit yard sale, basically.
I'm pretty sure I hooked up the battery wrong last time.
Reading these forums makes me think I need to find the fuse.
I looked all over next to the solenoid and under the dash and can't find one.
It turns over fine, and I don't think fuel is the problem.
I don't have a helper atm and can't think of a way to check for spark, working alone.

A few wires are connected with what look like big gobs of plastic.
What are those? Was there a fuse there before?

Thanks in advance for any help.
It is sort of a project boat, so I might be around here for a while. haha. 0905151228.jpg 0905151228a.jpg
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
No Title

If the starter runs, the fuse is ok. But here it is if you want to look for yourself. BTW the gobs of plastic are diodes in the shift circuit. Leave them alone unless you have good reason to mess with them.
 

Attachments

  • photo229594.jpg
    photo229594.jpg
    96.1 KB · Views: 0

smlJohnson115

Cadet
Thread starter
Joined
Sep 5, 2015
Messages
10
So it is. Thanks!
Now I just have to wait until I have another set of hands to check the spark. I guess.
If the fuse didn't blow from reversed terminals. I wonder what I might have messed up.

The oil/gas might be a little heavy on the oil, but I thought that would just make it smoke, not refuse to catch. It looks like gas is getting to the plugs.

I noticed a frayed wire leading to the switch earlier, so I disconnected it and put a new end on, and hooked all three up a different terminal on the switch accidentally, one that had nothing on it. Then moved them back. I can't tell what is positive and what is negative under there. The one that was frayed was purple and has a gob of plastic on it. It is in the sunlight in the first picture.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
The gob of plastic is a "Blocking Diode". It supplies voltage to the shift switch when the key is on, but blocks the alternator from feeding the ignition when you turn the key off. If the diode is shorted (burned out) the motor won't stop when you turn the key off.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
You need to use a volt meter (multimeter) to check for voltage at the purple wires on the terminal block on the backside of the motor, when the key is turned on. If you have battery voltage there when the key is on, the key switch is doing its job. The ignition system on that motor is quite complex. CDI has a website telling how to troubleshoot it, but I don't know the url offhand. Technically, you have a "Battery CD ignition", with an amplifier and breaker points. EDIT: I stand corrected, you have Battery CD ignition with a pulse pack and solid state sensor. (end of edit). A factory service manual is of little help because it tells how to troubleshoot it with an obsolete neon test instrument. Messing with it without knowing what you are doing almost always results in a blown pulse pack ($$$$$). One thing for certain, if you hooked the battery up backwards, you blew the alternator rectifier. But that isn't keeping it from running. Good luck, you are going to need it. But you will be a lot smarter once you master it.
 
Last edited:

smlJohnson115

Cadet
Thread starter
Joined
Sep 5, 2015
Messages
10
I don't show any voltage from either purple wire to the block, with the switch in the on position, but not cranking.
I checked the fat red wire that attaches to that thing right behind the started (solenoid?) and it shows 27 volts with my multi meter.
I expected 12. My battery also shows 27 volts. It is the one that came with the boat.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
27 volt battery?? Nah. Not unless you have two of them in series. Or a charger on it.
 

smlJohnson115

Cadet
Thread starter
Joined
Sep 5, 2015
Messages
10
No charger on it, but I did have one on it before. I bought the charger used. Maybe it worked too well or something. Or my multi meter is goofy. I'm going to try it on my truck battery. I usually only use it on home current.
 

smlJohnson115

Cadet
Thread starter
Joined
Sep 5, 2015
Messages
10
That was just me setting the meter on AC.
I tested the terminals of the switch, and one that did get hot when the switch was on wasn't hooked up to anything, and the one I was using didn't show current at all, so I switched the wires to the one that did come on, and tested the purple wires again, and they showed current. So I packed it all up, lowered the lift and started the boat. It was scary how fast it kicked in. I usually have to crank it for a while. Ran around the lake for ten minutes and then brought it home.
So from what I can tell, if my rectifier is bad, the battery won't charge back up at all.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
If you connected the battery backwards, it is a sure guarantee that the rectifier is burned up. You cannot disconnect it fast enough to prevent that from happening.
 

smlJohnson115

Cadet
Thread starter
Joined
Sep 5, 2015
Messages
10
My only hope may be that the entire time i had the cables reversed i also had the switch wired wrong, and never sent bad juice through. Plan to run it a while then check the battery. Or check it while running if my son can lend a hand.
 
Top