Johnson QD -15 won't start

mtemen

Cadet
Thread starter
Joined
Jul 4, 2017
Messages
6
I inherited a QD-15 from my father. He hadn't touched it in over 35 years. I have completely rebuilt the lower end and carburetor. I haven't touched the head assembly. My problem now is that it won't start. I have checked the spark and that's fine. However, after pulling the starter rope several times, and then checking the spark plug, it appears completely dry. I am wondering if no fuel mixture is getting to the crankcase and then up to the cylinders.

I have checked the fuel feed and believe that the tank is pressurizing properly and getting fuel "through" the carburetor. I have used starting fluid and it will give a promising pop or slight turnover, but then ...nothing.

Any ideas?
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Pretty new to outboards, and I have no background on your engine..
Just a few thoughts...

​First.. Are you sure the carbs are cleaned thoroughly? Idle passages clear?
Also, Float set right and not upside down?

​Finally... I wouldn't use starting fluid at all! It's not a fuel oil mix and could actually damage the engine as I understand it..
​Try spraying fuel/oil mix from a spray bottle into carb throat, or into spark plug holes, then trying..

​Also.. Do a compression test too...

​Again.. I'm NO expert, but just a few thoughts to start with?

Quite sure the experienced folks here will be along shortly to offer much better insight!

​For what it's worth..
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Welcome!

I believe the '54 has a view plate to allow you to get a look at the magneto. Remove the recoil starter, and then the plate. You're looking for coils that are not cracked or disintegrating. Replace them if the casings are cracking, as they will let you down. You can also set the points from the top with a gapping tool -- .020. Use a little acetone or lacquer thinner when checking the point gap, as the contacts need to be squeaky clean. Check the spark with an open air adjustable tester ($10 or so at an autoparts store). You need about 3/8" crisp spark. Remove the plugs for testing so you can give it a good spin.

Compression checking requires a tester, screw-in style (may be able to rent or borrow one). Somewhere around 100 and even would be good. Again -- plugs out for testing. Pull it over until the needle stops moving, then go on to the other cylinder.

Not sure what you mean by rebuilding the lower end, but need the impeller changed out -- maybe did that. Test in some kind of barrel with water about half way up the leg. You should get water from the port on the rear of the leg after the first or second pull, and immediately when it fires up. Operating temp is 120 to 140F, and varies some with water temp in the barrel or the lake. Over 160F is too hot (too hot to touch as well).

Carb needles are set about 1 turn open for the low speed needle (top one), and about 5/8 open for the high speed needle. These are initial settings that are meant to get the motor up and running. When warmed up, the settings are adjusted (See the sticky up at the top of the forum.)

Fuel ratio is 24:1, and some use 16:1. Don't worry about fuel and exhaust debris in the barrel while testing. Plugs are Champion J4C, gapped to .030. The throttle won't fully advance unless in gear. Start in neutral with the throttle at a high idle ("start" setting on the tiller handle, give or take -- don't put too much stock in the markings.)
 

mtemen

Cadet
Thread starter
Joined
Jul 4, 2017
Messages
6
Thank you oldboat1. You mentioned a lot of important stuff.

OK...I forgot to mention that I have replaced all the points, condenser, coil and spark plugs. All are gapped properly. Fuel mixture is fresh @ 24:1 I have checked spark, but not to my satisfaction . I am going to get a real spark tester and see if I get a "crisp" 3/8" spark. I also have NOT changed the plug wires. They looked ok to me. I clipped off a 1/4" before screwing on the new coil and it looked clean. I'll pick up some copper wire just in case when I'm at the parts store.

I also discovered that the fuel filter was pretty dirty at the bottom of the bowl. I removed and cleaned it pretty well, then reinstalled it. It looks like a pretty common filter so I'll pick one up and get in place too.

I also discovered a broken gear which is part of the tiller assembly. It's a pretty important part because it affects the throttle position. I ordered the new part today and will get it working shortly.

I tested the compression today to find 78 top and 81 bottom. Which I think will be ok for now.

Above all, my major observation is that no fuel is getting to the spark plugs. I have pumped the heck out of the fuel tank and get fuel leaking out of the lower high speed jet [I think i need new washer there] , so I know it's passing through the filter. But shouldn't the plugs be soaked with gasoline when I overdo it like that?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
gets to the plugs by running or cranking. Check the needle settings and use a couple of needle washers on each. May need to be sure that the float assembly is correct -- should not be able to continue priming when carb bowl is full.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
If you really are convinced the fuel is not being pulled into the cylinders, check the reeds. But that is unlikely.

EDIT: If the plugs were wet, it would indicate the motor is flooded. It wouldn't start if it is. In other words, they are not supposed to be wet.
 

mtemen

Cadet
Thread starter
Joined
Jul 4, 2017
Messages
6
As I pump the fuel tank to full pressure, it DOES stop, so I don't think I'm OVER priming. I'm going to replace the washers on both needles since there is some leakage there. I assume that will force fuel through the carb instead of out the jets. I realize that the plugs aren't supposed to be wet, but they are completely dry, which is the opposite problem. As old boat1 stated above, fuel gets to the plugs by being sucked in from the intake of the cylinders, so I'll just have to keep it up until the fuel arrives (or not). Since I haven't removed the powerhead assembly, is it safe to assume there are no obstructions of the intake manifold? It appears pretty large so I assume not.

The advice and suggestions given here are very helpful and informative. Thanks to everyone to contributing.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Pumping the tank does NOT pressurize the tank.---It fills the carburetor bowl with fuel.---When motor starts air is pumped into the tank to keep fuel flowing.
 

mtemen

Cadet
Thread starter
Joined
Jul 4, 2017
Messages
6
I finally had time to get back in the shop for the day yesterday. I checked the spark and observed that on the first 1-2 pulls I get a nice healthy spark, but after that nothing. Even though I have replaced all the ignition parts; plugs, points, condenser and coils. All have been adjusted properly. Could there be a faulty condenser or other component? I have also checked the plug wires and they appear to be fine.
 
Last edited:

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
guess from here is that there is a faulty connection. You might use a multi tester to check the plug wire connections through the coil. With your tester set at 1K ohms, test resistance between the spring connector in the plug to the mag plate. You should get a reading of 5 or 6K. More important for a new assembly, though, you need to see a reading. If you have no reading, you have no electrical connection to the plugs.

The connection at the plug is often a problem (spike has to go through to the wire core). Similarly, the coil spike has to contact the wire core.

The other likely culprit is the points setting or condition -- even new points need to be cleaned (acetone or lacquer thinner, or similar).
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
To start, you need to pull that carb off, soak it overnight, completely clean and rebuild. Assuming the passages are clean after sitting 35 years is asking too much of the old girl. While you are at it, change out the fuel lines to ensure they are clean, without holes, and are ethanol resistant.

Regarding the ignition system, very hard to guess here without an inspection. As stated, even new points need to be dressed and cleaned. Even out of the box. Fingerprints can limit spark. Can you post pictures of your ignition system? Maybe we can spot a problem.
 

mtemen

Cadet
Thread starter
Joined
Jul 4, 2017
Messages
6
I spent a good part of this weekend working on this project. Discovered that the upper cylinder is firing pretty well, but the lower one isn't firing at all. So i swapped the condensers between the two cylinders. Nothing changed; upper fired, lower didn't. I then pulled the plug wires and ohm tested them. My reading was really weird. With multimeter set to 200 ohms, I have a reading of .5 ohms for both wires.(basically NO resistance). Continuity is fine for both wires.

Should I have swapped the coils too? Points? (both x2 are brand new). (This weekend I will clean with acetone as suggested however.) I also read that the crankshaft can be turned in such a way before installing the flywheel (by aligning the keyway towards the coil), so the points ride on the shoulder of the cam to avoid the flywheel pushing down on them via the cam nut and damaging the points.) I inspected the points today and didn't see any damage from my prior novice flywheel installation.

I re-gapped the points today as well. They didn't need much adjustment. I adjusted to the high side of .020...

I am ordering new wires to install next weekend. (but since both wires ohm tested the same, I don't expect any improvement). I read recently that the coil end of the wires needs to be stripped down 1/4" to expose the strands after folding down against the wire insulation, THEN screwing the wire into the coil. I didn't do that, but will do so next weekend. Can I expect that to make a difference?

BTW, I am testing the spark using my electric drill on the top of the crankshaft with the spark plugs removed. (I'm testing the spark, with a common spark tester, by grounding on the motor at an unpainted area.). Works really well and a lot more fun!

I have also read some information about the fly wheel magnet needing recharging. I checked that today using a small magnet and it appear to be pretty good. Small magnet jumped out of my hand onto the flywheel. North and South.

It seems to me that everything covered above is pretty minor regarding my spark problem. So I'm really doubtful that any of the things I'm going to do will make much difference. Does anyone have any suggestions that I haven't covered here?

Thanks to everyone for their input. It's really nice to know that there are folks out there who care about these old motors!!!
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Problems aren't usually with the plug wire itself, but with connections at the coil or at the plug. Type of wire makes a difference -- need 7mm solid core, typically copper core. Contact has to be with the wire core at both coil and the plug spring connector.

The test I was describing is meant to test connections from the plug end all the way through the coil to the plate where the coil is mounted -- tests your assembly.
 

mtemen

Cadet
Thread starter
Joined
Jul 4, 2017
Messages
6
Spent some time in the shop today. I tested and installed new plug wires. Still spotty spark. Then I tested the coils (which are new) to find that the primary windings ohm'd out with no resistance. I also continuity tested them with success. Then I checked the secondary windings on the coils and got NO reading at all on BOTH coils. I believe I should have gotten a reading of 3-8K. So is it a valid conclusion to assume the NEW coils are BAD?

At a point during the day, I did test the spark with moderate success on the top cylinder and very inconsistent spark on the bottom cylinder. Odd thing is, i DID get some spark on both cylinders. But no where near anything consistent.

Throughout the day, I also swapped the plugs and points. Also with very inconsistent results. None of the symptoms transferred these parts.

I think I'm going to order two new coils and start over...

Thoughts?
 
Top