Johnson MQ-13b Hole in Gear Case?

Dorje

Recruit
Thread starter
Joined
Oct 18, 2016
Messages
4
Good day fine folks..I have searched the forums for similar questions and found none. I have what appears to be an interesting scenario and was wondering if some one here could provide me with some insight. I have had a 1967 Johnson Mq13b for years. It has always cranked on the first few pulls and ran like a champ. I love it. About 10 years ago I ran it and it would run great and then cut off. I found out I had crap in the gas... I parked the motor on a stand in my garage and life and several kids took over. The motor sat for the last 10 years.
Recently, my boss told me of a gentleman who works specifically on old Johnson motors. My son (who is 12 now) wants to start using the old john boat so I figured I would service the engine and get her going again. I gave my boss the motor and asked him to deliver it to said gentleman who got the motor working, "tip top" he said. Cleaned the screen, carb and put a new plug in it. Cranks right up he said.
So today I get the motor back. First thing I notice is gear oil under the motor when my buddy and I put it in my truck. When I got home I started looking for the source of this mess. Right above the prop on the bottom of the gear case is a small hole. My eyes are not what they used to be so I am having a bit of a time determining if the hole is supposed to be there. gear oil was coming out of the hole when it was on its side in the car. I have never had oil leak when the motor was transported in the past. I took some photos of this hole and hope that some one on the forum may have a similar motor and tell me if this tiny hole is supposed to be here or not....
Now the motor is upright on its stand and its not leaking gear oil any more. However I dont want to run it without making sure I aint gonna mess it up.
I have not started the motor since I brought it home as I need to find a gas can that does not sound like a maraca when I pick it up.. lol.
I will attach pictures
Thanks a zillion before hand and I hope one of you generously fine folks may be able to let me know this hole is good or bad!
It doesnt look good to me!
Ryan
 

Attachments

  • IMG_1973.JPG
    IMG_1973.JPG
    77.1 KB · Views: 0
  • IMG_1974.JPG
    IMG_1974.JPG
    89.5 KB · Views: 0

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Perfectly normal. It's a casting drain. If it weren't there, water would collect in the cavity above it and freeze in colder climates... The oil you're seeing is likely unburnt fuel/oil mix that has collected in that cavity...
 

Dorje

Recruit
Thread starter
Joined
Oct 18, 2016
Messages
4
Awesome. I wanted to make sure before I got out the JB weld... haha!
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
Take it out and run the heck out of it and then check it again.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Do the drippings smell like gas/oil/soot? Or does it stink to high heaven? Gear oil stinks to high heaven and the stench is just about impossible to wash off.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Any or all of the answers above may be true. OR, it could actually be gear oil. Since laying on it's side is a factor, it can be gear oil leaking out of the shift rod seal or the bearing housing/seal/gasket below the water pump (gravity, y'know--doesn't run uphill when standing up).

So, now it is up to you to determine if it is unburned fuel coming from the exhaust, or gear oil as you suspect. Unburned fuel is normal, gear oil leakage is not normal. BTW, yes some old gear oils did stink, but not all gear oil stinks.

And yes, the drain hole is there on purpose.
 
Top