Johnson carburetor

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
Can anyone tell me what year this carburetor is from....Casting # on carb is 376872. I am having trouble with my motor running too rich and not wanting to rev up at all. I located another carb with this number on it and it has both the low and high speed adjustments. The carb I have with the same number only has the idle screw and not a high speed adjustment. I'm thinking someone swapped carbs out at some point. I'm trying to locate which high speed needle valve to buy so I can try it. Thanks
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
So what motor do you have? No way to say what will or won't fit if we don't know what it is.
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
That motor/carb should have a fixed high speed plug. Part # 309415. I believe you need a special tool to remove it. If you can't remove the orifice plug, try soaking the bowl in carb cleaner overnight and then blowing it out as best you can. May clear the blockage if there is one. Problem may not be in the carb. Have you replaced the fuel filter? Will it run WOT if you squeeze the fuel line bulb? If so, could be the fuel pump.
 

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
When I pump fuel bulb it continues to bog down even more and smokes a lot more. Its running as if it is getting too much fuel and almost flooding out. I'm stumped on this one
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Stop----The best thing to do is some testing.----Does the primer bulb go hard when you squeeze it , yes or no?----If no do you see fuel pouring out of the carburetor ?----You may have a ruptured diaphragm in the fuel pump..----Nothing goes wrong with those carburetors that warrants replacing it !!
 

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
yes primer bulb does get hard. When I tried to pump it while I had it running it got to the point where I couldn't pump it anymore and I did not see any fuel coming out of the carb.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
you were unable to clean or clean/rebuild carb? maybe buggered up the h.s. jet trying to clean or remove it?

How about the fuel pump? any attempt at rebuilding or checking condition of diaphragm?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Could be running on one cylinder.----Does spark jump a gap of 1/4" or more on both leads, yes or no ?---For some reason the carburetor is the first item folks blame for motor problems.
 

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
yes spark jumps 5/16 gap easily blue spark on both leads. Motor stays running on cylinder drop test when disconnecting the leads (same response on both). I had the carb rebuilt this year but the h/s jet was not replaced, just cleaned. Just gaskets, needle, and float were replaced.. I did remove the h.s jet in the bottom of the bowl. It didn't appear to be damaged but who knows. I believe it had the number 64 engraved on it. I am going to try and order another. When I look at marineengine.com it gives two options for the high speed orifice which is the right jet ?
 

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
I did not try to rebuild the fuel pump, I did take the pump apart and made sure the screen was clear and put back together with no changes. How is the best way to tell if the diaphragm is faulty ?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
would need to disassemble the pump and look at the diaphragm -- looking for holes or tears, or loss of elasticity (old one can feel like cardboard and take a set. New one is a thin sheet of flexible rubber.)

[edit. don't know what to tell you about jet size. The one you have is probably .064, replacement is .063. 20 hp around '67 was .057(!), then early '70s 18s are .067. Go figure. Wait for wiser advice.... ]
 
Last edited:

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
think I should maybe start with fuel pump rebuild as long as I can find the right parts?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Well, the bad news on the fuel pump is that it's NLA -- and difficult to find a diaphragm. Good news is that you might not have the original pump anyway (didn't have a screen -- think you mentioned you had checked the screen). You may have the small square pump(?) which was a replacement. Kits are readily available for the square pump, although there are a bunch of small parts and good to have a parts diagram. LeeRoy's Ramblings has a good illustration (site seems to be unavailable at the moment, but this would be the main link: http://www.leeroysramblings.com/index.html .) Think I would find a diagram before pulling it apart, but when you get in there, the diaphragm should be flexible/supple, with no set. If it feels like cardboard, it needs to be replaced. Look for tears or holes, of course, even if otherwise in good condition. I think your model also has a glass bowl on the port side of the engine, with a peculiar filter that looks a little like a windsock -- unless bowl was removed by a PO.

Keep at it....
 

allegany23

Cadet
Thread starter
Joined
Jun 2, 2016
Messages
25
I do have an aftermarket fuel pump, the small square one, I have another motor that is a 6 hp evinrude fisherman that is a 1968 that runs great and it appears online that it is the same fuel pump(it also has the small square fuel pump that looks the exact same). I might try switching that fuel pump over and give it a try and see what happens. I will also check glass bowl filter to see if it has one.
 
Top