Johnson 9.5 won't idle or run.

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
OK, compression exactly 62 psi in both cylinders. I've seen these run at 60 psi, so that can't be the problem. They seem to run fine at that compression. Seldom see cylinders that close though! Good spark on both cylinders too. I'm wondering if it could be the idle needle. It looks the end outside the engine has had lots of vice grips on it over the years. The other carb had the cable type of turn mechanism on it that seems to not fit that carb very well, so it is possible that both are screwed up...literally.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Yes, I do no have that special screwdriver and that could be the culprit...What"s a guy to do? Where can I order one?
 

Crosbyman

Admiral
Joined
Nov 5, 2006
Messages
6,298
??? why would it shoot gas 5-6 feet with the choke off ??? the float and inlet needle should not permit that ???? please explain i am missing something
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Yes, the hose from the fuel pump to the carb. An easy and effective way to check fuel pump pressure and not have to take out the fuel pump filter. I've cleaned dozens of carbs and am good at it, multi carb engines included. I would not be here if this was a normal carb clean.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
One thing is that this is one of the few if not the only modern outboard down draft carburetor. There must be good reasons why they were not used much and discontinued after 1974, They run great when they run great in my experience, but...when they get problems are a bugger. They seem and are very simple, but sometimes simple can be complicated. Carbs in reality are air differential devices and work off different pressures of air volume, not just sucking in air like most think. Anyway, enough tech bull, I need to figure this thing out, but am almost ready to call it a day on this one.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
You too. BTW...that is not a jet in the bottom of the carb. A jet mixes air and fuel and that plug does not do that. So technically that plug is not a jet. Some may call it a jet though. Some even think Obama was a real president. lol The terminology is sometimes dim on outboards then there are some that think they know more than they do also.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
You are partly right> Car-bu-re-tor : A device that mixes a fine spray of fuel with air. All the parts house diagrams do not even show a "jet" for this motor. The jet is in the top portion of the carb and sticks down into the lower part where is sucks fuel from the long passage that contains what they call a something or other, but not a jet. Then there is a drain plug. An "orifice" is what one diagram calls it. Anyway, another one bites the dust as it runs like a champ now. I took the lower portion of that carb assembly off the parts motor and put it on the motor I want to run. So....that orifice was dirty (the bottom was cleaned, but was rusty) or something was defective, main culprit being that office. So in effect some of the posters were correct, I think. I think I'm glad they got rid of the down draft carb in 1974. It's a gas hog anyway. Another weakness of this carb is that the fuel sump/bowl is part of the carb pot metal casting. This makes it non-replaceable and I noticed that someone along the line scrubbed out one of these top carb sumps with a wire brush on a Dremel tool So the motor has good points (lightweight) along with the bad. Kind of like a lot of people.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Fact is there are several folks here that have knowledge of that 9.5 hp model.----Bring them the motor all in pieces and in boxes.-----They will assemble it in front of your eyes without a glance at a manual.----I have a minute and tell me how much you know about these motors !
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I wonder if they can do it in the dark under water like a Navy Diver? I don't use an manual on any outboard and have been broke down hundreds of miles from civilization in the North country and always get it done. Some of the best real life outboard mechanics in North America live here and never went to school for it. Some can tell by the sound of the motor what is wrong with it. I don't claim to be one of them.
 
Top