nurse loves fishing
Recruit
Thread starter- Joined
- Dec 3, 2017
- Messages
- 1
Hi all,
OK, been lurking here due to problems with Johnson gear lever stuck. Followed the advice here but no solutions. Went to a popular boating store, some f-wad in the shop sold me a can of pricey inox stating "that will fix the problem, as you have seized up the mechanism with salt and grime, take the L/U off, tip motor upside down and spray copiously down shaft"............Duff advice mate. The problem is with the plastic cantilever mechanism, not salt and grime or the gear change
shaft.. The problem is due to a very poor design.
Here is how we fixed the problem, and please note we knew nothing about outboards beforehand, only general maintenance. DON'T EVER FORCE THE GEAR LEVER. You will end up busting the plastic gear changing mechanism and the chances of getting a new one is next to zero.
1. Remove the L/U, it is very easy to do with a few bolts, then check if you can manually turn the gear shaft and the gear selector rod. If all is smooth and engaging well, the next step is as follows.
2. Don't waste your time trying to free the gear changing mechanism at the top of the U/U whatsoever. You will be wasting your time and money. Simply buy 3 + high tensile bolts, - 3/8 head UNC course thread 1/4 X 3/4 before you start as you are going to need them later.
3. Remove top cover and you will clearly see the mechanism in place is held in by 2 stupidly and very awkwardly located slotted screws. Take off the outer covers around the bottom of the motor and undo the choke lever assembly only, taking a picture of it with your mobile phone camera before undoing the linkages so you know how it goes back together rightly. . Next, undo the 2 3/8 nuts that hold the carbie to the inlet port and remove carb aside, leaving everything except choke cables intact. Next, undo the 3/8 bolts holding down the block, undo all and lift engine aside for easier accessibility to work on the slotted screws. Grab whatever sharp small diameter long cold chisel you can find and persevere striking the slotted screw anti clockwise until you can remove these 2 stupid screws holding down the plastic mechanism.
Once out, use a wide tool with a good bevel (we used to cold chisel) and gently pry out the plastic mechanism from the sleeve inside. There you will be astounded. What happens as I surmised is that the polyurethane sleeve and the plastic barrel expands with heat over time. When we took it out it was as dry as a bats arse and could never reinsert the barrel back into the plastic sleeve. We merely disconnected the mechanism, locked it into a workmate and gently used a 300mm X 20mm strip of 120 grade roughy and honed down the barrel,-maintaining its cylinder appearance until it smoothly went back into the plastic sleeve. Once a snug fit with about a ? to 1mm play on the side we smoothed off the barrel with some fine steel wool, blew away the debris from the barrel and sleeve with an airline, coated sleeve and barrel well with marine grease and reassembled. It should not be too loose and yet should be able to rotate left and right with no resistance . Reconnect the lever to the linkage and use those new high tensile bolts to replace the now buggered up slotted screws to refix the plastic swivel to the engine block. Assemble in reverse and reconnect the chock, and reapply the linkage to the gear lever
Use a torque wrench if fussy about the Nm torque. We just did them up with a hard pinch on the spanner. Reassembled everything in reverse to removal, hit the choke, 1[SUP]st[/SUP] pull, engine started and have had no issues since. To note, you will not experience any oil loss due to the engine being a 2 stroke and the lower gear assembly being sealed. I sincerely hope this helps fill the gap and resolve this common problem that I have noted throughout the forum. Why the entire mechanism has not been fashioned from cast aluminum with a stainless steel sleeve and barrel with a simple grease nipple to maintain integrity is beyond my logic.
OK, been lurking here due to problems with Johnson gear lever stuck. Followed the advice here but no solutions. Went to a popular boating store, some f-wad in the shop sold me a can of pricey inox stating "that will fix the problem, as you have seized up the mechanism with salt and grime, take the L/U off, tip motor upside down and spray copiously down shaft"............Duff advice mate. The problem is with the plastic cantilever mechanism, not salt and grime or the gear change
shaft.. The problem is due to a very poor design.
Here is how we fixed the problem, and please note we knew nothing about outboards beforehand, only general maintenance. DON'T EVER FORCE THE GEAR LEVER. You will end up busting the plastic gear changing mechanism and the chances of getting a new one is next to zero.
1. Remove the L/U, it is very easy to do with a few bolts, then check if you can manually turn the gear shaft and the gear selector rod. If all is smooth and engaging well, the next step is as follows.
2. Don't waste your time trying to free the gear changing mechanism at the top of the U/U whatsoever. You will be wasting your time and money. Simply buy 3 + high tensile bolts, - 3/8 head UNC course thread 1/4 X 3/4 before you start as you are going to need them later.
3. Remove top cover and you will clearly see the mechanism in place is held in by 2 stupidly and very awkwardly located slotted screws. Take off the outer covers around the bottom of the motor and undo the choke lever assembly only, taking a picture of it with your mobile phone camera before undoing the linkages so you know how it goes back together rightly. . Next, undo the 2 3/8 nuts that hold the carbie to the inlet port and remove carb aside, leaving everything except choke cables intact. Next, undo the 3/8 bolts holding down the block, undo all and lift engine aside for easier accessibility to work on the slotted screws. Grab whatever sharp small diameter long cold chisel you can find and persevere striking the slotted screw anti clockwise until you can remove these 2 stupid screws holding down the plastic mechanism.
Once out, use a wide tool with a good bevel (we used to cold chisel) and gently pry out the plastic mechanism from the sleeve inside. There you will be astounded. What happens as I surmised is that the polyurethane sleeve and the plastic barrel expands with heat over time. When we took it out it was as dry as a bats arse and could never reinsert the barrel back into the plastic sleeve. We merely disconnected the mechanism, locked it into a workmate and gently used a 300mm X 20mm strip of 120 grade roughy and honed down the barrel,-maintaining its cylinder appearance until it smoothly went back into the plastic sleeve. Once a snug fit with about a ? to 1mm play on the side we smoothed off the barrel with some fine steel wool, blew away the debris from the barrel and sleeve with an airline, coated sleeve and barrel well with marine grease and reassembled. It should not be too loose and yet should be able to rotate left and right with no resistance . Reconnect the lever to the linkage and use those new high tensile bolts to replace the now buggered up slotted screws to refix the plastic swivel to the engine block. Assemble in reverse and reconnect the chock, and reapply the linkage to the gear lever
Use a torque wrench if fussy about the Nm torque. We just did them up with a hard pinch on the spanner. Reassembled everything in reverse to removal, hit the choke, 1[SUP]st[/SUP] pull, engine started and have had no issues since. To note, you will not experience any oil loss due to the engine being a 2 stroke and the lower gear assembly being sealed. I sincerely hope this helps fill the gap and resolve this common problem that I have noted throughout the forum. Why the entire mechanism has not been fashioned from cast aluminum with a stainless steel sleeve and barrel with a simple grease nipple to maintain integrity is beyond my logic.