johnson 2.3 hp problem.

oceanman

Recruit
Thread starter
Joined
Apr 20, 2016
Messages
2
Hi all, just got my hands on a used Johnson 2.3 hp, not sure the year but the serial number is H O9275466. model HJ2RENR


Anyway I can not seem to get it to run smooth, it seems to need to be on choke or half choke all the time, I changed the plug and cleaned out the tank and the carb, all seem fine. is there something im doing wrong? greatfull for any help. thanks.
 

fhhuber

Lieutenant
Joined
Jun 19, 2014
Messages
1,365
Some assumptions (because I can't get the exploded views to come up... something wrong with model number)
Assuming you have a diaphram based fuel pump either in the carb or separate from the carb
assuming that engine has reed valves
Probably good assumptions....

Needing choke on all the time is indicating a fuel starvation issue.

Does it run a short time fine then need the choke? If so, open the gas cap and see if that cures it. The tank may not be venting.

Is is sucking the primer bulb flat? (if using a separate tank) That is either lack of tank venting or something plugging the fuel pickup. (rarely a stuck valve in the primer bulb)

Could be the diaphram in the fuel pump

Could be one of the tiny passages in the carb is plugged. Pull the carb apart and run a stiff copper wire about the diameter of the wire in a twist tie through the holes. The soft wire will bend before you hurt anything. Use canned air computer keyboard spray (not cleaner... just air) to blow through the passages. You may not even see anything come out but cure it...
Caution... make sure you don't blow out small springs or other parts and lose them...

I got a free riding lawnmower one time... it would run 30- to 40 sec then die. Sit 5 min and it would do it again. The boss gave up and said take it.
Turned out to be a stick in the fuel line.

Small chance of the reed valve having problems. Is it kind of blowing fuel out the carb?

Your worst case is a new carb or fuel pump. The reeds wouldn't be too bad to replace.
Someone else may be able to figure out the reason that model number comes up invalid.
 
Last edited:

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
Someone else may be able to figure out the reason that model number comes up invalid.
Ocean man has already asked about this engine on the UK's YBW.com forums. See http://www.ybw.com/forums/showthread.php?454742-johnson-2-3-problem

I suspect its a rebadged far eastern made model that was imported into the Europe and the UK but not the USA.therefore does not appear on the US parts websites.

The basic model number, H2REN, appears in http://web.archive.org/web/20020221005200/http://www.evinrude.com/docktalk/modref/jomodyr/JHP2.html

and in http://shop.evinrude.com/media/document/ModelNumberReference.pdf

I think you will find its a simple gravity fuel feed from an integral tank with no fuel pump involved.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Could be one of the tiny passages in the carb is plugged. Pull the carb apart and run a stiff copper wire about the diameter of the wire in a twist tie through the holes. The soft wire will bend before you hurt anything. Use canned air computer keyboard spray (not cleaner... just air) to blow through the passages. You may not even see anything come out but cure it...
Caution... make sure you don't blow out small springs or other parts and lose them...

Did you do this? I soak the metal parts after complete disassembly, then do what fhhuber describes. (I also use some carb spray.)
 

oceanman

Recruit
Thread starter
Joined
Apr 20, 2016
Messages
2
yes I did and it seems to have solved the problem, touch wood! many thanks for all the help.
 
Top