Johnson 115 bumps at higher RPMs

wmitchell02281999

Recruit
Thread starter
Joined
Jul 10, 2003
Messages
4
Bought 2001 Johnson 115 used. Ran fine for 12 hours but then started "bumping" at the higher speeds, starting at 30-35MPH. It started off slow, with one bump ever so often... but now has gradually gotten worse to bumping every few seconds. Shop guys say could be lower unit gears slipping/skipping, but wanted to get your input before spending the dough. Could it just be the prop hub slipping? Water in gas? Dirty carbeurator? Doesn't happen in water tank, only under load... thanks in advance.
 

rrichard

Seaman Apprentice
Joined
Jul 25, 2002
Messages
38
Re: Johnson 115 bumps at higher RPMs

(clarification)<br />Do you mean the engine is misfiring?
 

NOSLEEP

Commander
Joined
Oct 30, 2002
Messages
2,442
Re: Johnson 115 bumps at higher RPMs

Check your spark plugs, Its possible they are <br />failing under load, or a bad spark plug wire.
 

wmitchell02281999

Recruit
Thread starter
Joined
Jul 10, 2003
Messages
4
Re: Johnson 115 bumps at higher RPMs

Got new plugs. Shop guys tightened up the linkage which helped a little. Been reading other posts for few weeks and just found a few that point to clutch dog being worn. Would that make the bumping happen only at the higher speeds versus just cruising along at say 20MPH??? And, typically how expensive is it to replace a defective dog - on my own? Through the shop guys? Thanks again.
 

steelespike

Supreme Mariner
Joined
Apr 26, 2002
Messages
19,069
Re: Johnson 115 bumps at higher RPMs

Most likely a worn clutch dog.A fairly<br />easy repair for the mechanically inclined.<br /> On some motors you can reverse the dog so the<br />worn side works reverse. Forward and reverse gears<br />are always in mesh with the drive shaft and simply ride on the prop shaft.The dog is splined to the prop shaft and slides to ingage the forward or reverse gear.<br /> Get yourself a manual and look over the gearcase.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Re: Johnson 115 bumps at higher RPMs

Mitch.... The following may be of interest to you as it sounds like your problem.<br /><br />(Jumping Out Of Gear - Manual Type)<br /> <br />This pertains to lower units on all OMC manual shift outboard engines, or any OMC engine with lower units defined as a Shift Assist or a Hydro Electric Shift unit which incorporates a "Shifter Clutch Dog".<br /> <br />Within the lower unit, splined to the prop shaft is what is most often referred to as a clutch dog, hereafter simply called dog. The dog has at least two lobes protruding from it on both ends, facing both forward and reverse gear. The forward and reverse gears also have lobes built into them near their center area. When the engine is running, in neutral, the gears are spinning constantly via the driveshaft being connected directly to the powerhead crankshaft, but the propeller does not turn due to the fact that the dog is centered between the two gears, and the dog lobes are not touching either of the gear lobes.<br /> <br />When the unit is put into either gear, shift linkages force the dog (and its lobes of course) to engage the lobes of the the gear. The lobes of the spinning gear grab the lobes of the dog, and since the dog is splined to the prop shaft, the propeller turns.<br /><br />The lobes of the dog and gears are percisely machined, most with right angled edges that could be installed in either direction, and some with angles slightly varied that must be installed in one direction only (one end only must face the propeller). Dogs that can be installed in one direction only, if reversed, even if the dog and both gears were new.... would jump out of gear almost immediately. Keep in mind that the lobes are percisely machined with sharp angles!<br /> <br />Due to improper adjustment or worn shift linkages, but usually due to improper slow shifting, those percisely machined sharp edges of the lobes become slightly rounded. Now, with those lobes rounded, as the rpms increase, the pressure of the gear lobes upon the dog lobes increases to a point whereas they are forced apart (jumping out of gear), and due (usually) to the shift cable keeping tension on the engines shift linkages..... the unit is forced back into gear giving one the sensation that the engine has hit something, and the cycle continues.<br /> <br />Some boaters have the mistaken belief that shifting slowly is taking it easy on all of the shifting components..... Wrong! Shifting slowly allows those percisely machined sharp edges of the dog and gears to click, clank, bang, slam against each other many times before they are finally forced into alignment with each other..... and this is what rounds those edges off! The proper way to shift is to snap the unit into gear as quickly as possible.
 

wmitchell02281999

Recruit
Thread starter
Joined
Jul 10, 2003
Messages
4
Re: Johnson 115 bumps at higher RPMs

Thanks go out to Joe and the rest of you that have way more knowledge than myself... Sounds like "I gotta go see a man about a dog"... or find that manual and try it myself... :cool: You guys rock!!! :) Thanks again.
 

dixieray

Cadet
Joined
Feb 26, 2002
Messages
27
Re: Johnson 115 bumps at higher RPMs

Did you get it fixed??? I am working on mine, bought for. rev. and penion gears, water pump kit, lower end gasget set, clutch dog ( edges worn on drive gears and dog), tripple gard grease gasget sealer, shifter lever, plastic gears in shift handle, etc. cost so far $800.00 and I still am not sure I have the right impeller.
 

walleyehed

Admiral
Joined
Jun 29, 2003
Messages
6,767
Re: Johnson 115 bumps at higher RPMs

Joe, am I thinking wrong, or would that also show up when dropping the hammer and pushing water until on plane??? maybe not but seems like thats when most prophub problems show up, and it seems like gear stress would be extreme at that point as well............WOT is still pushing a lota load though...I'm guessing you've hit the mark on worn parts-those gears catch hell down there!
 

wmitchell02281999

Recruit
Thread starter
Joined
Jul 10, 2003
Messages
4
Re: Johnson 115 bumps at higher RPMs

Not fixed yet... :( so can't catch any fish... I put it in the shop a few weeks ago 'cause I know nothing about boat motors... still waiting on parts was my last update from them... quoted me $650... hopefully it'll run like a champ afterwards... will post when I get it on the water and test her out... thanks again to all.
 
Top