Johnson 1 1/2 hp flywheel won't go back on right

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Just for shoots and giggles I have been restoring this Johnson 1970 1.5. I cannot find a id plate. The job is going ok and then I get the flywheel on and it will not turn much and catches it seems on a metal protrusion that is part of the stator plate that holds the coil and points. Why is that there and can anyone tell me why the flywheel catches on that. I turn the manual spark and timing advance but still cannot get the flywheel free so it can spin so I can check spark. This seems kind of foolish as I have worked on numbers of larger outboards successfully..
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Move the coil back to where the laminated core is flush with the machined edges on the posts the coil is mounted on. That will set the correct clearance between the coil and flywheel magnets.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Thanks guys, but I know about that and checked it 2 times already. .I will check again, but it seems it is something else
 

Tim Frank

Vice Admiral
Joined
Jul 29, 2008
Messages
5,354
It would be really great if there was a form/template that an OP had to use to open a thread that is seeking assistance.

After the obvious Make, model, and HP, it might be something like :

Is this a new problem? Yes.....no.....
Is the motor new to you? Yes.....No....
If new to you, has it ever run properly? Yes.....No.....
etc.

So, could you answer those Qs?
If it is new to you...AND has never run properly....you cannot assume anything is correct.
Start by verifying that the right coil is installed....could have been an "owner mod" gone wrong.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Ok, I have been around outboards for 40 years. I don't claim to know as much as some here, but am not a newbie. This is the first time I have taken this size outboards fly wheel off, but have taken off flywheels of omc 3, 6, and lots of 9.9/15. It ran not good so I cleaned the carb and got new ignition parts. The new coil seems to be right as it common to many models and hp. I'm sure it ran properly at one time. There is a nub that is part of the stator/plate/timing plate that is about the size of your small fingernail and less than a half inch high. One of the magnets that are enclosed on the flywheel seems to be hitting this, keeping the flywheel from turning. If I hold the flywheel a quarter inch hgher It does not hit this nub. I at first thought that maybe there was a shim to hold the flywheel higher, but schamatics do not show any and also the flywheel would not be tight on the spindle. It is very very perplexing.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Well, there is a washer under the armature plate -- appears to fit under the liner (cyl to armature plate). Numbers 35 and 33, respectively, on the diagrams I looked at. I can't remember putting one together, so just looking at the parts diagram(s). (There is also a gasket up there on the topside of the plate, apparently.)

I wonder if that washer is missing in your assembly. It would probably push the liner up further and raise the flywheel slightly higher off the plate(?)

This is one of the diagrams I looked at: http://www.iboats.com/Magneto-Group/dm/cart_id.790298497--session_id.420152780--view_id.1545039
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Yes, that is what I thought. 33 is the plastic collar that is there and 35 is a thin plastic shim washer that looks a lot thinner than in the diagram. I am going to post a photo of that nub.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Ok, so here is a photo of the plate. The protruding nub on the far right that looks like stair steps is where the magnet is hanging up when I spin the flywheel. Does anyone know what that nub does?
 

Attachments

  • DSC09206_edited-1.jpg
    DSC09206_edited-1.jpg
    224.5 KB · Views: 0

StarTed

Senior Chief Petty Officer
Joined
Jul 14, 2015
Messages
694
I don't know anything about this motor so I'm only guessing.

Maybe it's there to prevent from getting the flywheel too far down. Did you have the crank out and maybe have shims wrong on the main bearings?

That should get some experts to chime in.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Interesting. I'll take one more shot at it (again, no hands on experience with the 1 1/2).

The armature plate is described/pictured in the diagrams as a plate and post assembly. I see the post on the right side of the plate in your picture, but it looks like there is a horizontal piece missing. That piece would seem to rest on the lowest stepped portion of the nub that is giving your trouble. The horizontal piece would parallel the bottom of the flywheel, as I interpret the diagram.

The configuration of the armature plate in the parts diagram seems slightly different than yours, but probably immaterial. Your coil, breaker points and condenser appear to be located correctly (not too many ways to go wrong). I can't tell from your pic whether the coil laminations are absolutely flush with the mounting posts, but you've verified that. I think from the look of it that the magnet should rotate outside of machined edge the nub.

Afraid my only suggestion is that you mount the missing horizontal piece (if I see the diagram correctly), and check the assembly of the coil again. Unless the clearance at the coils is dead on perfect, the flywheel won't slip over both the coil laminations and the machined edge of that nub, as I see it.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
No, did not take crank out! Oldboat, I will check on what you describe and get back here with the findings!
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Ok, so where did you see the diagram? I use the ones on Boats.net and that protrusion is hidden behind the finger grab throttle arm. I see no way a horizontal plate could go on as there are no screw of bolt holes. What is really weird about this is that this motor is about as simple as they come. I have worked on larger more complex ignitions and no problems like this at all. It must be so simple it is complicated, if that makes and sense!
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Think I led you wrong, thatone. I compared a parts diagram here at iBoats with your pic -- that horizontal piece I imagined late last night is apparently molded into the throttle plate (i.e., it's part of the plate shown in your pic). Ain't no additional part.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Okkkkk, Where is my tight fitting Duncecap? I started thinking simple. I kept turning the flywheel until I could hear the knocking of metal. I did not originally get the coil and flywheel magnet correct. I could feel some give after untightening and retightening the coil screws. I could see that the magnet was getting scraped by the flywheel magnet. I got the flywheel to turn now, but it is still scraping somewhere, but some work and adjustments and it should be good. This is one of those questionable designs of the coil adjustments that old Mercury might try to make better and actually make it harder. Or is that my excuse?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
hey -- excuse is good here, if you let me off the hook too!

Sounds like progress with the little bugger....
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Wait a minute! Maybe I'm not totally to blame! Although the flywheel turns now, it is still scraping the arm that adjusts the coil sliding in and out. Can I file this arm as no matter what I do to the adjustment screw and the 2 set screws, it does not change. It is probably an after market job and not good tolerance. I have never see a coil this squirrely.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Maybe the coil is binding at the wire (grommet jammed up, maybe)? Think I would first try to lift up the plate again and set the wire at the coil, then try fitting the coil. Maybe it's got to move a little bit laterally in order to go properly into place.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Well, Something I should have checked early in the game was the collar thin plastic shim that the mag plate revolves on. Part #33. I now notice that the mag plate wobbles and is not tight. What threw me off, is that the bolt tightener that has a large spring on it and really tightens down against the shaft part of the assembly that could be made super tight. I think this might be the culprit as when I wobble the plate the flywheel will rotate free of hitting anything. The part should be here in 5 days.
 
Top