How bad would it be to remove that buzzer and not replace it?

BigStew

Cadet
Thread starter
Joined
Jun 11, 2017
Messages
12
1990 Evinrude 60hp VRO(vro is removed). Been running pretty well, but last time we tried to start it, the battery died after only a few attempts. I removed the battery and tried to start with one of my truck batteries. The motor started, but something in the ignition housing started to smoke. So I pulled the power cables away from the battery, and in a few seconds the motor died(it died cause it was cold- it would have kept on running had it been warm, IMO). We took the boat home and parked it. Today I pulled the cover off the ignition and found what was smoking. There is a buzzer/beeper connected to a relay-looking box that is wired into the ignition. This box has 3 inputs- one is a ground, one is labeled as "accessory", and one I think is a group of inputs on one line that causes the buzzer/beep to happen. I've only ever heard it do the beep upon initial key turn. So the little relay-looking box leaked that nasty liquid that comes out of these kinds of electrical boxes when you let the smoke out. I hate that crap- it stinks, and it's hard to get off. Anyhow, I haven't figured out how to trace the purple accessory lines yet, but I looked in the motor and found that mauve-looking wire's sources(at least I think so). While I was reading about the buzzer/beep box, it said the buzzer goes off if the tach races too high, if the engine gets too hot, and if the oil reservoir in the VRO gets too low. Can't remember if there were any other reasons for the alarm buzzer to sound. Like I said, this motor's VRO has been removed, and I found two of those mauve wires in the area where the VRO used to exist. So I was wondering if one of those wire ends might have contributed to my issue(they're not exposed ends- they have the old connectors on them)? I haven't tried to put the multi-meter on them yet, or on the accessory wires, or the ground. But I will soon. If you have any input, or questions, please share them. Thank you for your time.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Well,
​Pretty new to outboards here, but even if the VRO is removed, so you're not getting the low oil, no oil, fuel restriction alarms, If you remove and don't replace the warning horn, you'll never know if you overheat via the temp sensor.
​If you overheat, and keep running, good bet you'll destroy your engine.

​But, I'm a relative newbie, but I wouldn't take it out and not replace it..
​At least make sure the overheat buzzer is working for piece of mind while operating.

​For what it's worth...
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
The buzzer only matters if there's ever an issue, it sounds so you can hopefully shut the motor down before it self destructs. If this doesn't matter to you, then there's no need to replace the system, it just requires a new motor after it comes to a stop. While that sounds like I'm being a smart&@@, I'm not, If you don't care, it really doesn't matter.
 

BigStew

Cadet
Thread starter
Joined
Jun 11, 2017
Messages
12
You guys make good points, and the one about requiring a new motor once it comes to a stop was really funny... and enlightening. I had the same idea. I posted this for a few friends on facebook, and one of them suggested just removing it. I figured it would only matter when it came to the over-temp. It was quick-fix thinking. I'm guessing I need to put the meter on the lines, especially the mauve one that seems to be the offender(by the looks of the connector being covered in goo). I'm just used to searching for what I think is the problem and coming up with rabbit holes.

If that one connector/wire seems like it was the problem, would it indicate it had shorted to ground?
 

cfauvel

Chief Petty Officer
Joined
Aug 16, 2005
Messages
645
I'm lost ....is it the buzzer that is smoking? if so that isn't anywhere near the engine, its at the helm.


if you've disconnected the VRO (oil side or the whole thing), then I assume you've removed the oil reservoir and the only thing you have left that the buzzer will warn you about is the overheat condition (unless it is a V6, then it will warn you of fuel obstruction).

I personally don't like running my engine without everything working perfectly(or near perfect)
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
If that one connector/wire seems like it was the problem, would it indicate it had shorted to ground?

:lol::lol::lol:

The correct and proper operation of the warning horn is DUE TO THE FACT that one of those tan wires has shorted to ground by the associated sensor.

Temp gets too hot, sensor switch shorts the tan wire to ground, horn sounds.

Tank runs low on oil, tan wire shorts to ground, horn sounds.

That's the way it works.

If the tan wire was permanently shorted to ground by a fault, a pinched wire in the boat somewhere, etc., the horn would never stop alarming.

By the way there ain't no mauve wire colors on an Evinrude!!!!! Too pansyfied. Ole would be rolling in his grave. Mauve....
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
If the purple wire is shorted to ground, everytime he turns the key to ON, the engine fuse will blow.

I believe the purple sends the power to the buzzer. Probably I am wrong though.

Too many amps into it would make it smoke.
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
Purple on all modern OMCs is always "Key ON, switched 12v".

An electrical load (the buzzer) is what determines the amount of current that flows. Not the source. The battery has 900 possible amps available to send to the load.
Just because it has 900 amps available doesn't mean all that current goes to each load.

"Too many AMPs into it would make it smoke...." The only way to get too many AMPs into it is for the module to be defective, with a very low internal resistance, thereby allowing excessive current to flow.

If the PURPLE wire is shorted to ground, the LOAD is effectively the wire itself. The purple wire is then the load with regard to the electrical circuit.
The path for current would be +12v batt terminal, red/purple wire from engine thru 20 amp fuse to key switch, key switch to purple wire to negative batt terminal.

There is very little resistance on that path, and will blow the fuse.
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
Ahhhh...this thread is so messed up anyway....

The module he describes as leaking burnt fluids sounds like the horn driver module with the horn connected.
However, that was not used on 1990 models. So, what is he describing? The horn itself? It has three wires...purple, black and tan (mauve) LOL.

Does he have a Systems Check harness and control (newer than 1996) with an older motor and an adapter to go from Deutsch connectors to big red cannon plug?

What is the motor model number?????

There is not enough accurate info here to figure out his problem.

But to answer his OP question....No, it is not a good idea to disconnect the horn and run without it.

Over and out.
 

BigStew

Cadet
Thread starter
Joined
Jun 11, 2017
Messages
12
No Title

I looked up mauve. Turns out it's purple, and not tan. Anyway, here are some pictures of that buzzer module. It does indeed have 3 connections. When I looked it up, I found that the black is the ground, the purple is the power, and the TAN is the signal. I put my trusty multimeter on the contacts and found that the black ground connection is electrically the same as the purple power connection. I'm sitting here with a light bulb above my head. So I'm pretty sure I'm going to order me a replacement for this module.
 

Attachments

  • photo272432.JPG
    photo272432.JPG
    43.6 KB · Views: 0
  • photo272433.JPG
    photo272433.JPG
    44.5 KB · Views: 0
  • photo272434.JPG
    photo272434.JPG
    44.5 KB · Views: 0

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
I've gone to Radio Shack and replaced them with louder...and far cheaper alarms.
 

BigStew

Cadet
Thread starter
Joined
Jun 11, 2017
Messages
12
ondarvr, is it a simple thing to use a different alarm? I expect I'll need to go that route, seeing as the correct ones are pretty expensive.
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
I used something similar, just got the loudest one I could find.
 
Top