hour meter

Hellman

Recruit
Thread starter
Joined
May 2, 2011
Messages
1
2006 3.0l Volva Penta I/O carb motor. I want to hook up my hour meter so it works only when the engine is running. I know it won't make that much difference than just hooked up to the ignition, but that's the easy way. I've tried hooking up my hour meter to the couple of wires when the boat is running, but all that does is not make the hour meter work, and the alarm chirp every 30 seconds or so. I don't want to go off the altenator if I don't have to, so can I go off the oil pressure guage, or the tach, in my guage cluster already? I read one guy say to not go off the tach, and something about T-ing off the oil pressure with another sensor?
 

Lyle29464

Lieutenant
Joined
Mar 10, 2009
Messages
1,261
Re: hour meter

Just tie in to anything that works with the key in the on position. Gas gauge maybe? why would you have your key on and the engine not running? I guess you could make it hot and hook to a switch that grounds when the engine starts? maybe oil pressure?
 
D

DJ

Guest
Re: hour meter

It's not unusual to tie it into the oil pressure circuit. That DOES avoid clocking hours when some moron (like me) leaves the key on for three days.:eek:;)
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: hour meter

You hook the POS wire from the hour meter to the "I" (ignition) terminal on any other gauge. This puts 12 volts on the meter whether or not the motor is running. The ground connection goes to the oil pressure switch. When the engine startes and oil pressure rises, the oil pressure switch (not the oil pressure sender) closes thus starting the meter. The oil pressure "sender" is a resistance element that works with the oil pressure gauge and can't be used for this function. You could "T" an oil pressure switch into the same port if you wish (provided the engine doesn't already have one). You cannot use the ignition wires.
 

stevtech

Cadet
Joined
Aug 22, 2010
Messages
20
Re: hour meter

Hi
I put a latching relay on my hour meter. The coil is in seriese with the start switch. It latches when the Start switch is on and stays on during run. When turned off it drops out. Now if I turn it back on for just the radio or lights it does not record hours.
Funny thing is I read 26 hours. Took it in to Cabelas and they said it had 37 hours on it. Optimax 75 on a Lowe FM165. Seems like mercury might just be counting hours when the ignition is on and the motor is not running.
 

stevtech

Cadet
Joined
Aug 22, 2010
Messages
20
Re: hour meter

I didn't have wiring diagram so I don't know how the tach is wired. If it is on the ignition wire on the tach it will clock if the ignition is on but the motor (start) has not been turned on.
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
Re: hour meter

You cannot run the hour meter from the tach "sense" line for the simple reason that that line is NOT a constant 12 volt feed. It is a pulsed line and nowhere near 12 volts. An hour meter needs only 12 volts and ground to operate because it is a simple clock mechanism. Put 12 volts on it and it runs. Connect it to +12 volt source with the key on and then find IF (note that I said IF) you have an oil pressure SWITCH (Note that I said oil pressure SWITCH -- not SENDER), you can connect the ground lead to the oil pressure SWITCH. Now the meter would run ONLY when the engine is running.
 

AZSenza

Chief Petty Officer
Joined
Mar 11, 2008
Messages
521
Re: hour meter

Silvertip is correct, You'll need a "T" with an oil pressure switch as well as the pressure sender on it. You' be amazed how many hours will show up with the key in the on position from Sunday night to the next Sunday morning! My boat shows 550hrs, its been left on twice-PO and me! In reality that motors got maybe 300 Hrs on it.
 

stevtech

Cadet
Joined
Aug 22, 2010
Messages
20
Re: hour meter

Thats why I used a latching relay. Off, On and start. Start activates the coil and Run holds it in. When switched to Off the relay drops out. Go back to run and it will not turn on untill start pulls the coil in again. One set of contacts used as a latch, the other set switches the Hour meter on. Seemed easier to me. I don't know anything about the oil pressure switch or where to access it.
 
Top