Help with strange seacock / water intake problem

Necatour

Recruit
Thread starter
Joined
Dec 23, 2011
Messages
3
Hi,

My first posting here. I hope you might be able to help out. We are about to buy a sailing boat (Contrast 36) and during an inspection we found a problem with the intake "holes" which sucks in cooling water on the saildrive on the Yanmar engine (though, we do not think the problem is related to any specific brand). The holes have become much larger and deformed over time and it seems like an on-going process. One theory is that the damage is caused by an electrolyte process when different metals are used on the saildrive and another one is that there might be a problem with the electric wiring on the boat. Please see the attached images. Any input to this would be much appreciated!

Thanks,
Henrik

Photo 2011-11-23 12 21 08.jpgPhoto 2011-11-23 12 21 16.jpgPhoto 2011-11-23 12 24 54.jpg
 

Fireman431

Rear Admiral
Joined
Sep 17, 2007
Messages
4,292
Re: Help with strange seacock / water intake problem

Appears to be galvanic corrosion. That usually occurs from improper bonding of all the metal components in the boat and/or reaction of AC shore power in your electrical system. You didnt indicate the condition of your anodes and what material they were composed of (zinc, magnesium), and what type of water the boat is moored in.

Need to get a little more info. Check the electrical bonding system and look for corrosion on the wires/bonding lugs. Check your zincs. Are you connected to shore power? Have a test done at the dock to see if there is electricity leeching into the water. Sometimes an additional sacrificial anode may help (a fish zinc), but you can be over zinced.
 

Pez Vela

Chief Petty Officer
Joined
Dec 4, 2004
Messages
504
Re: Help with strange seacock / water intake problem

Marine corrosion is difficult to troubleshoot without knowing the boat's history. It appears that the lower unit has suffered from electrolysis, the source of which could be its own systems, or that of other boats, if the boat has a history of being slipped in a "hot" marina. Attempts to patch and paint the area are apparent. The boat needs to be put in the water and tested for stray current by a knowledgeable person.
http://marinesurvey.com/yacht/corrosion_1.htm
 

Necatour

Recruit
Thread starter
Joined
Dec 23, 2011
Messages
3
Re: Help with strange seacock / water intake problem

Thanks Fireman!

The initial inspection unfortunately did not go into all the details of the wiring :-( ... the overall condition of the boat is excellent. Though, what we know is that it's "home" is in the river Elbe in Hamburg, Germany (freshwater). It has however been used in the North Sea and the Baltic (mix of fresh and salt water). It is using shore power and the anodes are of zinc. The owner added a fish zinc some time back and says the process has slowed down/stopped. This is of course good but in order to buy the boat we need to be sure of this. Also, the damage might already be so severe that we may have to replace it (the saildrive's protective iron "box")? Thanks again for any additional input!

Best regards,
Henrik

Appears to be galvanic corrosion. That usually occurs from improper bonding of all the metal components in the boat and/or reaction of AC shore power in your electrical system. You didnt indicate the condition of your anodes and what material they were composed of (zinc, magnesium), and what type of water the boat is moored in.

Need to get a little more info. Check the electrical bonding system and look for corrosion on the wires/bonding lugs. Check your zincs. Are you connected to shore power? Have a test done at the dock to see if there is electricity leeching into the water. Sometimes an additional sacrificial anode may help (a fish zinc), but you can be over zinced.
 

Necatour

Recruit
Thread starter
Joined
Dec 23, 2011
Messages
3
Re: Help with strange seacock / water intake problem

Thanks Pez!

More details above :) The only problem is that the boat is currently on land for winter storage. It won't be in water until early May. We will try to find a boat electrician but as you say, it might be difficult troubleshooting being out of the water? Right now we are concerned whether the damage is already so extensive that it (saildrive "box") needs to be more thoroughly repaired/replaced? Thanks for any additional input!

Best regards,
Henrik





QUOTE=Pez Vela;3580426]Marine corrosion is difficult to troubleshoot without knowing the boat's history. It appears that the lower unit has suffered from electrolysis, the source of which could be its own systems, or that of other boats, if the boat has a history of being slipped in a "hot" marina. Attempts to patch and paint the area are apparent. The boat needs to be put in the water and tested for stray current by a knowledgeable person.
http://marinesurvey.com/yacht/corrosion_1.htm[/QUOTE]
 
Top