Fresh motor getting hot

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
Just rebuilt the power head on my 73 135 evinrude. Started it up and it ran good water coming out of the pew hole but also coming out of the seam where the lower unit meets the midsection. Also water stopped coming out of the pew hole and it started to get hot. After 10 min the heads are almost too hot to touch. Now my timing advance didn't wanna hit the stop all the way forward would that cause it to get hot. O and it has a whole new water pump kit
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
No Title

Here's a picture
 

Attachments

  • photo239737.jpg
    photo239737.jpg
    265.3 KB · Views: 0

64osby

Admiral
Joined
Jul 28, 2009
Messages
6,826
Pull the lower and check the impeller. Then check for any blockages.
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
I know the pee hole hose isn't blocked its clear. The impeller and all that is brand new.
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Your 73 engine is too old to have a telltale coming from the powerhead. That overboard indicator did not start until the 78 model year. So, there are a couple of ways to determine if it's overheating: 1. the overheat horn will go off inside the control box when it gets up around 200+ degrees. 2. You can measure the head temps with a laser temp gun. Be sure to measure it when idling and when it's on plane in the lake. It's cooling system functions differently between idle and planning. Your single vernatherm (thermostat) should open around 115-120. It should idle maybe up to 130 when idling in the lake. The hot horn will sound around 200, and will silence when it gets back down to maybe 175. (Still too hot) There is one thing you can look out for: start the engine when it's cold. Put the palm of your hand over the two exhaust relief ports just under the rear cowling. After a minute or so, the vernatherm will open. (this is a good sign) When it does, water droplets will start to form on the palm of your hand. That's normal. That mist is about all you'll see from the powerhead. On old engines, it's not unusual for the grease under the timer base to thicken to the point that the base does not move easily. Take the flywheel off and then the timer base. Clean all the old grease out and re-apply some white lithium grease, commonly known as 2-4-C in the marine industry. Doubt it's sticking has anything to do with overheating.
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
I added the tell tale. I know the motor is tilted with the trailer bar if that makes a difference. The timing isn't sticking but something broke in the controls so it might not be sitting where it's supposed to.
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
Also how hot should the water from the tell tale be ? And what temps should the heads be at idle?
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
Yes but at idle on muffs should the water out the pew hole be hot?
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
The normal telltale on the later engines is plumbed into the exhaust cover. The water flow from the lower unit comes up through the exhaust adapter, and into the back of the engine first. So, the telltale will have cooler water than that coming from either head. On your engine, the cooling water takes two paths inside the engine, depending on whether the vernatherm is open or closed. That could make a slight difference in the temp of the water at the telltale. I would not suppose that it would be much above the 130 mark. If the telltale is 150 or more, you could have a bad vernatherm. As a point of clarification, normally on any engine rebuild, the rebuilder will protect his work by installing a new vernatherm. Do you know if this was done?
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
No Title

Vernatherm came from a working unit. I pulled the lower unit apart the water pump looks as it should. However the exhaust seal was not seated and looked rough would that cause water to spew out where the midsection and lower unit meet? One more thing, my muffs broke yesterday so i rigged up a coupling from a coolant flush kit had a one wat check with a very small hole. Im thinking it was not getting enough water.
 

Attachments

  • photo239767.jpg
    photo239767.jpg
    201.2 KB · Views: 0
  • photo239768.jpg
    photo239768.jpg
    131.8 KB · Views: 0

James R

Commander
Joined
Feb 1, 2007
Messages
2,681
You say that the motor is tilted and you are using muffs. Some motors don't like that. Get a barrel and set the motor in vertically ensuring that the water level is above the pump.Keep the hose running into the barrel because the exhaust will try to blow the water out of the barrel. I do a lot of motors and this is the way if you don't have tanks.
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Interesting that the big exhaust seal in your hand does not match the opening it's supposed to seat into. Any chance you have a seal from another lower unit? The shapes don't appear to match up. Double check you part number. The lower exhaust seal could have been mis-installed. That could cause water to leak out of the seam between the lower unit and the bottom of the midsection. But since that water is coming "from" the powerhead (already been circulated thru the block) whatever leaks from that crack is of no consequence.
 
Last edited:

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
Interesting that the big exhaust seal in your hand does not match the opening it's supposed to seat into. Any chance you have a seal from another lower unit? The shapes don't appear to match up. Double check you part number. The lower exhaust seal could have been mis-installed. That could cause water to leak out of the seam between the lower unit and the bottom of the midsection. But since that water is coming "from" the powerhead (already been circulated thru the block) whatever leaks from that crack is of no consequence.

It seems that way but I do think it's correct the one side looks likes it's been rolled like it caught an edge Thats why it looks flat. I may just load it up with some gel seal or rtv and call it a day since eaither way it's used water
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
The opening in your picture that the lower 135 exhaust seal sits in is rounded on one end. The later (dual thermostat) crossflows use a rubber gasket which is more squared off, similar to the one in your picture.
 

rodknee1231

Petty Officer 2nd Class
Thread starter
Joined
Jul 28, 2015
Messages
136
Is it possible that if my crappy jerry rigged muffs weren't flowing enough water that the pee hole would flow right off the bat but once the vern opened it dropped the pressure down low enough it wouldn't flow through the pee hole
 
Top