Evinrude 9.5 frozen mag plate?

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I cannot make out totally the model #..It looks like 9122R. Serial is JL2336. Probably around 1970 give or take a year or 2. I got this cheap as it had a broken tiller handle and I found out why. The mag/timing plate seems frozen to the crank shaft or whatever it attached to. I took out all ignition parts and bolts and now just the plate is there. I also removed all the shift linkage and still it will not turn or move up or down. I have changed a number of ignition sets like this and don't get what is wrong. Any one experience this? or know what is wrong? or how ​I can free up this.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
So, you say you have removed all the ignition parts. Does that include the coils? If you did remove the coils do you remember the screws toward the center? Those screws hold the plate down. BUT there are two more between the coils and points. Those are also holding the plate down. Loosen those and the plate can be removed. However you say it is stuck and won't move. That would be very unusual, but it must be stuck to the neck on the crankcase that it pivots on. You will have to apply whatever scientific means (penetrating oil, force, whatever) it takes to break it free.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Yes Indeed, I know it is unusual, that is why I put the question on here. All screws are out except the offset point adjustment screws that do not hold it down as they are short. One coil had some rust on the bottom and a few more rust areas on the motor so it probably is a rust problem maybe. The 9.5 does have a peculiar mechanical lever system to control the mag and spark, but I have disconnected it all.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Gotta be seized by rust and corrosion. It should lift off with ease.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I have tried a claw hammer prying from the block to the point that I was afraid I would break the pot metal type mag plate. Also tried a very large screw driver, no go at all???? This is Weird!
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
All I can tell you is that in my 24 years of OMC service work, I have removed a few thousands of those things, never had a problem. If the four screws are out as you say they are, it should lift right off. Since you say it won't, you are going to have to get mean with it. See if you can get it to rotate back and forth with some of the magic penetrating stuff first to break it loose. Only caution I can offer is if something breaks, it might be the neck on the crankcase. If that breaks, the show is over.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I kinda know what you mean as I have take off a few of them myself and no problem, ever! This is amazing as I keep at it with claw hammers, pipe wrenches and anything else I can find that will get a grip on it. I do notice that I was putting the penetrating oil on the inner shaft area instead of the exact machined line around that neck where it meets the plate...we shall see. Yes, I have to be carefull not to break that neck, you are right!
 

kbait

Commander
Joined
Nov 13, 2007
Messages
2,488
At this point, you may want to use a drill/dremmel tool etc and surgically destroy the armature plate to remove. Then just swap to a used plate.
Good luck!
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Or clamp visegrips at the edge and smack back and forth with a hammer to rotate it?
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I am trying the vice grips, with little effect. I was hoping some 9.5 guru would tell me there is a hidden set of bolts or screws holding it on. Funny, for years I have read this forum and have saw some crazy problems related on the posts. I always thought to myself, gee, I am lucky to never have any of these weird problems. I guess it is my turn now!
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The magplate is held on the 9.5 just the same way as all the other 1,000,000 motors that used this magneto plate.------Nothing hidden , no magic to it.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
I've been told to take a torch to it, that may be the next step. Yes, I guess I knew that it was the same on a million others, just was wishing! Still can't budge the dam thing.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
OK Here is the photo with the vice-grips attached. I have been whacking the grips back and forth but leery of damaging the flywheel. BTW. I had a prop shaft bearing so stuck in the housing I had to take it to a machine shop and even they had trouble today The guy tore out the rubber and then welded a bead of weld that gave a grip for a slide hammer to pull on and it came out. I am having very bad luck lately with stuck stuff!!!
 

Attachments

  • DSC09150_edited-1.jpg
    DSC09150_edited-1.jpg
    273.3 KB · Views: 0

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Yep, nothing holding that plate (in theory). Must be corrosion. One has to wonder why. That is supposed to have lubricant where it pivots, and should not corrode. Unless it has suffered submersion in salt water or something. If that is the case, it isn't worth messing with anyway. Let us know how it works out.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Now I've got a big 3 arm gear puller on it. I'm going to go for broke and turn it slow on and off until it comes off or something breaks or it flys off and tries to hit me.
 

thatone123

Banned
Thread starter
Joined
Mar 7, 2009
Messages
707
Well. the 3 arm bandit gear puller got it off. You know how when you take off a flywheel it does that cracking sound? Well. this did that finally and I thought I could remove it. But, no, I had to put the puller on again and it cracked 6 times with increasing pressure while it moved a 32/d of an inch with each crack and finally came loose. OMG, what a mess that spindle and the plate and the removable plates under there. A caked on black mess that seems almost burned on. White layers of ugly white salt and green caked on slop. I am using a screw drive to scrape it all off. It is very hard and old.I don't think the penetrating oil penetrated!, or maybe just slightly. Anyway, thanks for the input​! America-love it or leave it!
 
Top