Evinrude 9.5 (9922S) carburetor rebuild

RogueGeek

Cadet
Thread starter
Joined
Jan 9, 2017
Messages
6
Greetings,

I searched the forum but couldn't find anything. So I figured I would post and ask for assistance.

I have a '69 model 9.5hp Evinrude that I am going to rebuild the carburetor on.
This is my first time working on an outboard engine and I have a question regarding the rebuild.

There is a core plug (I think that is the correct term) with a plastic filler behind it. Is it necessary to remove and replace these during the rebuild?
I have the parts, but if it isn't really necessary, I would rather not start an invasive operation on my carburetor to remove these.

thanks for your assistance.

Brian
 

Attachments

  • CarbRebuild1.jpg
    CarbRebuild1.jpg
    124.4 KB · Views: 0

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Not much goes wrong with carburetors.--------What is the motor doing / not doing ?
 

RogueGeek

Cadet
Thread starter
Joined
Jan 9, 2017
Messages
6
The engine has been setting unused for several years and it appears the previous owner attempted to "fix" the motor but failed miserably.
The carburetor had been taken off and left in pieces inside the engine cover. Old brittle gaskets and o-rings.

So basically I'm just trying to undo the last guys mess and put it back together and get it running.

So far I have found leaves stuck in the reed valves, the thermostat was corroded, and the throttle linkage and tiller gear wouldn't move do to being so gummed up with grease mixed with sand and dirt.

Other than that, it appears to be in fairly decent shape.
The rest of the engine is clean and visually looks to be in good condition.

Once I get it running, I'll see if it needs a water pump rebuild and any attention to the lower unit and drive train.

-Brian
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
sounds offhand like your motor might have been dunked at some point.
 

RogueGeek

Cadet
Thread starter
Joined
Jan 9, 2017
Messages
6
It guess its possible. I didn't see any signs of water or other corrosion on the engine.
What should I look for to try and figure out if it went for a swim??

I set a limit of $50 for repairs. If I can't get it running after rebuilding the carb and a new thermostat. I haven't spent so much on it that it hurts and I at least learned a bit about outboard engines in the process.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
I usually figure $130 or so for basic maintenance on a new-to-me motor. If it took a swim, what happened in the couple of hours after that makes all the difference. It's worse if they go in running, and worse yet in salt water. The recommendation is usually to disassemble completely.

If the motor pulls over smoothly, may be fine. If you are going to fire it up, do the water pump first -- busting up an old impeller creates all kinds of extra work.
 

RogueGeek

Cadet
Thread starter
Joined
Jan 9, 2017
Messages
6
I don't see any evidence of salt water or salt spray. So if it went in the water, it was most likely fresh water.

The ignition system seems ok and the spark definitely jumps a 1/4" gap. I'm going to check the gap on the points and the spark plug gap while I have things apart.

I don't have a compression gauge, but it seems to have pretty good compression and is nice and smooth when I pull it over.
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
Step 1: Always test compression. You need a gauge for this. No human other than spider man could tell the difference of say 10 psi! If you don't have one, many places loan tools, or ask family friends. Always do this BEFORE you spend any money.]

Step 2: Test spark. As stated above by Racerone, it should easily jump a 1/4" gap on an inline adjustable tester with a bright blue ZAP!! If it doesn't, you have issues. Possible issue, if those coils are original, they are junk. That is a certainty, even if they spark. They will fail on the water.

After these are done, then you go on to the fuel system, water pump, gearcase re seal, etc....

In general, you need to expect to put about $175 to $200 into a used motor of this variety. The ignition system alone costs over $100 in parts between the coils, points, condensors, plugs, plug wire, spark plug boots, etc...... Then after a carb kit, water pump kit, seal kit, etc etc it does add up. However after wards you have a reliable, motor which you can enjoy on the water. If properly taken care of these will outlast you.

Now, the 9.5s did have some trouble areas to be aware of. They very often have bad motor mounts. Pull on the powerhead fore and aft to test. IF they are shot, your motor will not run correctly as the vibrating will throw off the ignition. This job can be done, but can be intimidating if you have not done it before. Its a knuckle scratcher!~

They very often have bad exhaust boots as well. You often see the 9.5s with holes drilled in the cowling to provide fresh air and somewhere for the exhaust to escape to allow them to run. The new parts can still be had at www.nymarine.ca
 

ultra353

Petty Officer 1st Class
Joined
Jun 21, 2009
Messages
388
Leave that plastic plug there, probably won't be able to get it out anyways. there was too much volume in that cavity and they used that plug to take away the void to help idling. At least that's what I've been told.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
X2 what ultra just said. Leave it in there unless it is proven that it needs to come out. Symptoms would be it won't idle. No need to worry about that until you find out whether or not you have a viable motor.
 

RogueGeek

Cadet
Thread starter
Joined
Jan 9, 2017
Messages
6
Thank you everyone for all the great info. It is very much appreciated.
Depending on what my wife has planned for me this weekend :) I think I will set down at the workbench and do a thorough cleaning on the carb and try and complete the "rebuild" minus replacing the core plugs.

I'll post an update later with any news about progress or problems.

thanks again
 
Top