Evinrude 1981 4hp overheating badly, please help !

Daview

Recruit
Thread starter
Joined
May 15, 2016
Messages
4
Hi everybody, I'm completely new to outboards and boating. I have been an avid fisherman for quite some time and always hoped for a boat and outboard and just recently bought one. It came with an evinrude 1981 4hp 2 stroke outboard. I has a few problems trying to get it running but it's now running great except one thing, I took it out on my first trip and it was great at first but about 5 mins after running the engine it preheated and stopped working which was a bit scary thankfully I had oars. I took the engine home and inspected the impeller. It's fans are intact and are bent in the direction the blades were turning so I'm guessing it's worn so I've just ordered another one and it's on it's way. I blew out the lines leading up to the block and there's no blockage. The other thing I checked is there is a bend in terms housing of the impeller which could be drawing in air. But I really don't know what the issue could e as I'm no boat expert. Has anyone ever had a problem like this ? What could be causing ? Could really do with help as I can't afford to buy an outboard. Thanks
 

James R

Commander
Joined
Feb 1, 2007
Messages
2,681
If there is damage to the pump housing then you are most likely not getting sufficient water up to the motor. If the motor has been used in salt water you may have other issues.
 

tomhath

Master Chief Petty Officer
Joined
Dec 5, 2007
Messages
814
The fact that you noticed the pump body is damaged suggests that the last person who serviced the motor didn't do it right. I've found chunks of old impellers in various places besides the water tubes. In the pump, in the powerhead, etc. It's also possible (if you didn't check it when you pulled the lower unit) that the water tube wasn't connected to the pump properly when the last guy replaced the impeller. Another common problem is the little pin that fixes the impeller to the shaft is missing.

Replacing the head gasket on a two stroke motor is very simple, just take out the bolts and lift the head off - no valves to worry about. The head gasket itself only costs a few dollars. When you pull the head you'll see the water passages, make sure they're not blocked by sand, salt, etc. Most of the motors I've replaced head gaskets on have blocked water passages.
 
Last edited:

Daview

Recruit
Thread starter
Joined
May 15, 2016
Messages
4
I did consider the head gasket but didn't remove it I'm finding it difficult finding one for this model at a reasonable price. Looks like I'm just going to have to remove it and make sure that the passages are clear. Yep the housing does look a little warped at the base so it may be drawing air so buy I've managed to get a gasket for the pump housing. The small holes at the back of the boat do provide a small mist. I'll have a look at the head tonight and see if I can find a blockage. Thanks for the replies I'll keep u updated
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
It may also be worth separating the power head from the exhaust housing and cleaning out the water channels in the area the water tube discharges into .

Blowing air up the water tube is not a particularly good test because you can blow an awful lot more air through a restriction than you can pump water. Better to connect a water supply hose to the water tube to be sure you can get a good water flow
 
Last edited:

Daview

Recruit
Thread starter
Joined
May 15, 2016
Messages
4
Just thought id update u guys on what's happening with the motor. Was going to take the head gasket off and make sure all the cooling sections were clear of crap but the bolts are sized in place. Tried everything to get them off and sprayed them with wd40 and let it soak for a couple of days but still not budging. Looks like I'll have to take the outboard to a mechanic to get the bolts off and I can take it from there, if I do resolve this I'll let u know how I get on. Thanks for the advice
 

sutor623

Rear Admiral
Joined
May 23, 2011
Messages
4,089
Honestly, if it is giving you that much trouble, I would replace the waterpump housing and impeller and run her in the bucket. See how she feels. Then taker on the water with a buddy and keep the hood off and moniter the head temps.

If at that point it is still getting too hot, invest the time to get the powerhead up. There are small passages going in and out of the block of that motor, but if the waterpump fixes it let her fly.

Only reason I say this, is if you snap a bolt head off of the head, or powerhead base, you may be in for some fun. I have broken bolts off the heads of these little motors. They are not fun to get out.

Lastly, WD40 is not an ample rust dissolver. Try PB blaster or deep creep. You need something designed to free up old rust. Ever hear of the blue wrench? Propane torch has saved my @$$ numerous times with seized bolts!!
 

Daview

Recruit
Thread starter
Joined
May 15, 2016
Messages
4
Just an update guys, thanks for ur time and help. Took the head off the engine and blew it out no resistance whatsoever so was happy that the channels were clear. Reassembled with new impeller and it's working a treat now 😃 .... Took a while but at least I've learned a bit about outboards and got the problem sorted happy days 👍
 
Top