Evinrude 15 hp mid range adjustment

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
My 1987 evinrude 15 hp runs perfect at idle speed but as i accelerate, it starts 4 stroking ( galloping ) and then as the rpm's build it smoothes put and seems to be running ritch and suddenly cleans up and runs full throttle smooth and fast.
Basically, seems to be rich at mi-range and galloping at 1/3 of mid range. I've cleand the carb. any suggestions on repairing this problem would be greatly appreciated
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Use a timing light and see how spark behaves as you speed up.----Check both cylinders.
 

OptsyEagle

Lieutenant
Joined
Sep 13, 2006
Messages
1,367
Check your spark timing synchronization. I am not familiar with the 1987 model but there will usually be a mark on the throttle cam that pushes on the carb's roller when you twist the throttle grip. If there is a mark, it should be in the middle of the roller JUST as the throttle cam touches the roller. This will ensure your spark timing is correct over all RPM levels of the motor.
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
With the throttle at the lowest position, the throttle roller is centered the mark on the cam.
 

OptsyEagle

Lieutenant
Joined
Sep 13, 2006
Messages
1,367
Again, I am not familiar with the 1987 model, but my 1976 model will allow for a lower throttle position where the throttle cam does not even touch the roller on the carb. A reduced RPM is achieved by retarding the spark timing as the timing plate rotates. Are you saying that at the lowest throttle position the twist grip will give, the throttle cam is still touching the carb's roller?
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
Yes... It is touching the roller. Should i shorten the linkage. At the throttle cable so that the cam will rotate further?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
The plastic throttle control cam might be broken or the screw at the hight speed end needs adjustment. The cam clamps in place between the retainer and the armature plate, as I recall, and maybe it's not quite in the right place.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Check to make sure the covering is still on the roller and has not rotted off. The roller needs to start opening the carb at the mark, it may not even be close with the throttle retarded at idle. That cam is either not adjustable or has an external screw on it.
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
I've checked all things suggested. The ignition fire is good. Firing on both cylinders, the cam roller is now in the perfect position. But it runs smooth at idle speed but just above idle. It starts 4 stroking up until 3/4 throttle. when I hold it at full throttle, it seems to be flooding as it takes a few seconds to open up to full throttle. I had a thought last night...could this be caused by the float being set to high? As there is no high speed adjustment and it doesn't start this until the throttle is beginning to open and then clears up after running at full throttle for a few seconds and burns the excessive fuel, ????????
 

Stumpalump

Chief Petty Officer
Joined
Dec 5, 2013
Messages
413
Yes it could be float height. Use an ignition wrench set with the cocked open end to pull the carb. Pull bowl and hold carb upside down. The float should sit level with the carb body. Sombody said somewhere that those floats can get installed upside down. Idk...
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
Thanks..ive purchased a new needle and seat..this will be tomorrows project. Thanks!
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Do you have the early production or the late production carb: http://www.iboats.com/15-E15ECUD/dm/cart_id.092610043--session_id.965118325--view_id.1547381 ? Cleaning technique is a little different between the two.

(will note different fuel pumps used as well [early or late]).

Can look at the carb parts diagram to get a sense of the float orientation. At least on the late model carb, I'm pretty sure it goes on only one way (i.e., wouldn't fit over the nozzle if upside down).
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
btw, when throttling up -- are you doing that on the boat, with timing advancing (mag plate rotating)? Should not be simply opening the carb, manually operating the cam follower.
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
I think all is moving accordingly. The float was set at the correct position. Seems to still be running rich through out mid range rpm's. Now my question is, what meters the fuel at mid to high rpm's? Does the "nozzle well" do this? Part number 396605.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Has the float absorbed fuel? Most of, or all of the timing advance occurs before the carb really opens up, so that why proper sync between carb and timing is so important. When engine rpm are higher, but the carb is just slightly opened, the idle circuits are too small to feed enough gas to keep it running. There needs to be a system to provide fuel under that condition, ad there still isn't enough airflow for fuel to be drawn through the main nozzle in the venturi. It might be addition fuel feed holes/slot forward of the throttle plates. On some large motors, in order to provide enough air to let the engine idle, and provide reasonable off idle transition, the throttle plates often have one or more holes
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
46261.gif

Does part referance # 2 meter the fuel for mid to high speed rpm as their are no high speed mixture adjustment?
 

Attachments

  • 46261.gif
    46261.gif
    27.9 KB · Views: 0

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12


Does part referance # 2 meter the fuel for mid to high speed rpm as their are no high speed mixture adjustment?
 

IAV82

Cadet
Thread starter
Joined
Aug 13, 2011
Messages
12
0396605.jpg Nozzle well. Could some one opening the orifice too large cause the problem?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
not exactly. #23 is the orifice/jet that meters flow -- screws into the side of the vertical plastic nozzle. It may be that someone used the wrong jet, or reamed out the original. Want to be sure the gasket (#6) is in place.

The more typical problem with the jet is that it is not squeaky clean (would carefully clean it first -- can usually screw it out of the plastic nozzle without ruining it.)
 

Sea Rider

Supreme Mariner
Joined
Sep 20, 2008
Messages
12,345
Check when moving tiller grip to start position if the middle roller stops at middle mark shown on upper part of the timing plate, at that position carb will begin to open accordingly when throttling. Check when at full throttle if carb's butterfly is opened all the way. On this model the roller body has a screw that can be screwed CW or CCW for roller to reach that position, at the end of the cam there's another screw which can be adjusted CW or CCW for plastic cam's end to open carb's fully.

That's the procedure for correct carb and timing synch on an Evi 9,9-15 HP, don't know about the 8 HP model ? When carb and timing advance are synched spot on, there's nothing that needs extra adjustment as the carb will work all by itself once once fast idle throttle is passed.

Happy Boating
 
Top