Evinrude 140 won't Tilt/Trim

AZBoater19

Recruit
Thread starter
Joined
Aug 13, 2003
Messages
3
Need some help- <br /><br />Last time out on the lake, I did'nt have the slightest problem with the tilt/trim system on my 1986 Evinrude VRO 140. Now, it won't work at all, the tilt/trim motor isn't coming on at all, no clicking sounds or anything like that. I think I basically just need to know where to start, are there fuses on these systems? Is this common? Any advice will be appreciated.
 

2sunaz

Cadet
Joined
Aug 7, 2003
Messages
18
Re: Evinrude 140 won't Tilt/Trim

I see one fuse in the circuit on my 92 VRO 140. It is located directly below the cranking motor solenoid on the port side of the engine. Mine is in a red rubber fuse housing with metal safety clips. It is smaller than normal sized fuse(in length), and the amps depend on the size of electric pump you have. Hope this helps.
 

The Marine Doctor

Commander
Joined
Jul 25, 2003
Messages
2,177
Re: Evinrude 140 won't Tilt/Trim

The fuse that is in control of the T+T also controls the Ign for starting...if the fuse is shot..the engine will not turn over.<br /><br />^above might be too new.<br /><br />You say there is NO clicks at all?<br /><br />Unless your year is wrong...there should be a box inside the back of the boat that houses a fuse for the T+T. About 5X7.<br /><br />I do believe though...that in 86 there should be a box inside the engine compartment..this houses the relay's for the T+T. There should be a fuse in there.<br />There will be GREEN and BLUE wires running to and from it.<br /><br />TMD
 

AZBoater19

Recruit
Thread starter
Joined
Aug 13, 2003
Messages
3
Re: Evinrude 140 won't Tilt/Trim

Thanks for the info, it gave me a good start. However, I did some troubleshooting today, there in fact is a single click when i hit the switch, i must not have heard it the other day. Used my fluke meter to chase down power, Ive got 12.6 volts going to the fuse box, fuses are good, and same voltage comes out the other side. I followed this power all the way down to the hydraulic motor (pump?) And with the switch depressed the motor makes a really faint clicking sound, and warmed up slightly after a short time. Anyone have any advice? I think in the morning im taking that pump off, this will involve losing fluid, and might get me nowhere, so if someone feels the need to stop me... please feel free!! Thanks all for your info.
 

OBJ

Supreme Mariner
Joined
Dec 27, 2002
Messages
10,161
Re: Evinrude 140 won't Tilt/Trim

AZ...you can check the motor easily by direct connecting it to your battery. Disconnect the heavy green and blue wires from the relay box. Should be a connector on the back side of the motor. If you want to check the "UP"....connect the battery ground wire to the green wire leading to the motor and touch the positive side of the battery to the blue wire. Reverse the leads to check the "DOWN". Also you can have someone operate the trim switch and you can listen to the relays to see if they "click". On some engines I have found that the goo that is put around the base of the relays "melts" out and fouls the lead connections. So make sure all the leads in the relay box and connections to and from the box are clean.<br /><br />If the above tests prove that the motor is at falut, the brushes may need replace. These are still available from the Johnny/Rude dealers.<br /><br />Good Luck and keep us posted.
 

AZBoater19

Recruit
Thread starter
Joined
Aug 13, 2003
Messages
3
Re: Evinrude 140 won't Tilt/Trim

Thanks guys, just to let you know, it turns out the motor was at fault. I dropped the trim system today and removed the motor, upon inspection the brushes had in fact fused themselves together. I sent it out to an electric motor repairman here in town, to be rebuilt, by the sounds of it ill be back on the water in a few days. Once again, thanks for all your help... problem solved... for now. What next haha.
 
Top