Evinrude 120hp V4 Looper Idle Problems

Charlie43

Recruit
Thread starter
Joined
Sep 19, 2017
Messages
3
I am new and need some help I have a 1988 Evinrude 120hp V4 LOOPER that I purchased the last of July it is on a 1988 Procraft fish and ski the person I purchased it from said it was cold natured and ran rough until it warmed up. The first time to the lake when I got it started it would not idle I would have to keep it running with the high idle lever and sneak it into gear. One it was in gear it still would not idle I had to keep it at about half throttle one I got where I could throttle the engine up it ran good at full throttle. I took it home pulled the plugs they where fouled from over fueling. I install four new plugs set the gap order new carb kits installed kits set floats check the carbs to make sure they where all closed at the same time.Install new fuel line. The person I purchased it from had unhooked the VRO pump and I just mixed the fuel 50:1 as he had been doing.Back to the lake this time the engine started idle was some better but engine would not rev to full throttle with out missing.I removed the cover and adjusted the advance timing. This got me back to running at full throttle but still will die when at idle. These carbs have fixed idle jets can not be adjusted with out changing jets. What am I missing that would get the engine to idle.
 

gelcoat

Recruit
Joined
Jul 6, 2007
Messages
1
This is my order of operations when dealing with this, because it sounds like you have a dead cylinder.
1. Pull all plugs.
2. Bore scope each cylinder. ( Looking at piston tops )
3. Check spark for each cylinder.
4. Check compression.
Alot of people foolishly chase a fuel problem and over look the general engine service condition.
 

rothfm

Ensign
Joined
Sep 26, 2006
Messages
920
Like Gelcoat said, Baseline that engine..

Need to verify even compression
Check all hoses, for leaking, cracking etc
Verify Spark, ensuring wires are not arcing
Filters, Seperators

Pull some posts here, there is a proper and complete way to rebuild carbs. Ensure you did a full disassembly and cleaning with a wire strand.

There is a Link-n-sync procedure that puts things into proper function if done properly. But dont jump into that just yet.

I have a 1993 Looper that didnt idle either. It took a bit of work. Temperature DOES affect idle quality. On mine, It ran too cool always. Could never get it higher even after thermostat housing work.

I then found my Idle "bleed" adjustment on each carb was "out" less then 1 turn. Almost immediately, when I brought these out to 3-4turns, My temps came up to normal, idle smoothed out, and less smoke. I was not at a proper mix of air/fuel for efficient combustion.

Get the proper OMC genuine manual, find out how many turns "out" on the idle air bleed valves is recommended as a starting point, and go plus/minus to see results-do all at same time and test each time.
 

rothfm

Ensign
Joined
Sep 26, 2006
Messages
920
Oh, if you search on this topic you will see that these are known for NOT idling very well. However, if you do the diligence, you should be able to get it pretty decent. I was very displeased with mine when I got it, but now its almost as smooth as my crossflows-It can be done.
 

Charlie43

Recruit
Thread starter
Joined
Sep 19, 2017
Messages
3
I was on the road all week did not get chance to check my post but thanks guys, I got time to day and I started all over I scoped the cylinders and all four pistons and cylinder walls look good, no damage and run compression test 120psi on all four cylinders.My carbs does not have adjustable fuel -air mixture screws they have the fixed jets and they are marked 41 on the jets as the service manual calls for.What I did fine was some water in my carb bowls I removed them and checked all four float settings.I removed the fuel from the tank and put some in a glass and set it a side after couple hours there was water in the bottom of the glass.Question I mix my fuel and do not use the VRO pump if I install a water separator will it separate the oil from the gas.
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
You must service/clean the throttle bodies. The throttle bodies is where ALL the idle mixing is occurring.
 

Charlie43

Recruit
Thread starter
Joined
Sep 19, 2017
Messages
3
Has anyone installed thermostats on a Evinrude 120hp V4 looper. One of of mine was open and one was closed when I checked them. I order new thermostats and diaphragms I ordered the Oem not aftermarket but when I got them in the new ones do not set back again the round rubber seal in the head.The threaded shaft on the new thermostats that screw into the diaphragms are longer than the ones that I removed. If I loosen the thermostats in diaphragms I can get it to seal against the rubber seal in the head. But I am not sure how these thermostats work. The way these new one are made with just small holes for water to pass threw I don't believe that at high rpms there will be enough water passing threw them. It looks like the way the old ones are made when the engine is at high rpms the thermostats retracts letting water bypass around the thermostats. Question is if you have replaced these thermostats did you have the same problem do I have the wrong thermostats?
 

rothfm

Ensign
Joined
Sep 26, 2006
Messages
920
Charlie...im sort of new to 120/140 loopers but learning...there are differences between the years.

For what its worth....when i got my 1993 140 looper. I wanted to go thru the thermoststs. My OEM manual showed stuff I didnt have, but it showed a little thermostat within screw together Halves of a plastic body.

Thinking someone put the wrong stuff in my motor, i researched, and scratched my head. Turns out the design on mine changed about that year and my book showed pics of the Other style, which I couldnt do unless replacing the head, even then i think the block is diff too.

Guess what im saying if not done already, reference against an OEM manual, and a couple of the online cross_reference sites out there.
 
Top