e10relesc won't start - where to start - battery excellent

tinmanroy

Recruit
Thread starter
Joined
May 6, 2017
Messages
4
i'm not sure where to look, connected battery(+ to + and - to -) push starter, nothing, it is in neutral( can spin motor). put safety clip on. there are three plug terminals that are plugged into a three plug line that ends with 2 leads that go to battery. this motor was a backup on a larger boat. I just want to use it on my 14ft lund deep-v.
any help would be appreciated. thank you.. Roy:confused:
 

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
If all connections are clean and tight and battery is in good shape then maybe there is a fuse you can check. You say the safety clip is installed. Maybe make sure it is clipped in the right slot. I have made that mistake before. You can try using a set of jumper cables directly to starter to see if it will crank. The positive to the positive lug on the starter and the negative to the starter bracket. As well you can check voltage at the battery and then at the solenoid with the button pushed. If voltage at the battery side of solenoid but not at the starter side with button pushed would indicate a bad solenoid. EDIT Also make sure the start button itself is not at fault.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Is this motor a tiller or a remote model there is a big difference in the electrical systems on those..
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
If it was a remote it would have a key switch not a pushbutton which is what he is describing. He also makes no mention of the junction box which is needed for the remote model.
 

gm280

Supreme Mariner
Joined
Jun 26, 2011
Messages
14,605
So many possibilities for it not to start. But getting it to crank over would be the first thing to get working. Follow through with "Hardwater's" suggestions and post back.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
No solenoid on your 9.9 electric if the button is at the motor. The starter button under the steering bracket has a gaggle of wires behind it, and that could be the issue (or the button itself.) You do have a neutral safety switch down under the gearshift -- could check to see if the button engages and disengages with movement of the shift handle. Should have a cut off switch on the lower front cowl.

Hard to say how it was rigged by a PO, though. If set up for remote, for example, the location of the cutoff switch is moved to the front and the remote throttle cable goes in where the switch was.

[ed. if starter button still at motor, but remote steering and shift cables in place].
 

tinmanroy

Recruit
Thread starter
Joined
May 6, 2017
Messages
4
I can't give any definite answers yet. have to get through the rain and snow to check it out. you all have given me several good roads to follow though. It has the tiller and the safety swt is at the front of the tiller. starter swt is on the left below the gear shift towards the front. No remote cables. where might the fuse be?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Yup, no fuse unless a PO put one in.

Without firing it up or the battery connected, you can easily do some continuity testing for the ground, and then for the positive wiring in the starter circuit (incl testing the neutral safety switch). Check ground continuity from the negative battery clamp to the powerhead. Check the starter circuit from the positive battery cable to the stud on the starter (gearshift in neutral and starter button engaged). If you get continuity, you know the starter button is working as well as the neutral safety switch pass through. Then test with the motor in gear (should have no continuity).

The cutoff switch (the clip on the end of the tiller, in your case) can keep the ignition from firing, but isn't part of the starting circuit -- so not an issue for starter operation.
 

tinmanroy

Recruit
Thread starter
Joined
May 6, 2017
Messages
4
Gentleman, thanks for all input, got the wheels movin. Jumped starter first. Bingo, worked. Traced wiring back to starter set. Good. Traced wiring back to battery leads. Found some really hodgepodge wiring. Opens, da. Jumped to starter set with my wiring. Bingo again, pushed starter set and off we go. Will now get new wiring from starter set to to battery connection an den all will be Go in the pond.
Thank you all for your input. Problem solved.

Your Humble Servant,

Roy aka FTG2, retired
 
Top