Carb/Air flow problems on '62 Evinrude 3HP

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
All, I pulled an old Lightwin 3HP out of my father in-laws garage on his challenge to get it running. Changed out magneto with new parts and have good spark and new carb kit and cleaning for carburetor complete but engine only runs for 3-6 seconds then shuts off. Can anyone suggest possible problems?
Thanks,
 

Fleetwin

Lieutenant Junior Grade
Joined
Nov 23, 2011
Messages
1,141
Re: Carb/Air flow problems on '62 Evinrude 3HP

Did you replace the old cork float?

I assume this has the integral tank on top? The shut off valves can get gummed up.
 

steelespike

Supreme Mariner
Joined
Apr 26, 2002
Messages
19,069
Re: Carb/Air flow problems on '62 Evinrude 3HP

Speaking generically;there also may be a filter inside the tank on the outlet fitting.
My experience has been you can usually unscrew the fitting.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Re: Carb/Air flow problems on '62 Evinrude 3HP

Check the filter in the tank. It is part of the fitting that the shut-off is threaded into.

Also, is the screen present between the air horn and the throat of the carb? It MUST be there as it acts as a partial choke to richen the mixture.
 

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
Re: Carb/Air flow problems on '62 Evinrude 3HP

Air intake horn clean with mesh cover intact. Tank, Fuel flow screen and copper line already cleaned with a steady flow rate. Float was also replaced when I did new carb kit.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Re: Carb/Air flow problems on '62 Evinrude 3HP

If it ran more than 3-6 seconds, I'd say revisit that tank filter. But if that's the longest it will run, I suspect something other than fuel. How is the compression? Getting water in a cylinder??? I assume you've tried various carb needle settings.
 

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
Re: Carb/Air flow problems on '62 Evinrude 3HP

Supreme Mariner, the bottom (high speed) I set at 1 turn out from snug and the top needle (slow speed) I set at 1-1/2 turns out form snug, should I open or close from there? NO water in the cylinder
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Re: Carb/Air flow problems on '62 Evinrude 3HP

The integral fuel tank has a vent in the cover, as you probably know. It sound like you could lean out the slow speed needle a bit (clockwise about 1/8 turn at a time, pausing to let the motor even out after each adjustment.) I've usually found that the high speed needle ends up at about 3/4 open, so you might want to lean out the HS adj as well after you get the slow speed setting a little closer. The motor rpms will increase as you lean out the settings.
 

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
Re: Carb/Air flow problems on '62 Evinrude 3HP

Thanks oldboat & F_R, checked the compression and got at or less than 20 PSI for both heads so maybe it's also not drawing the fuel vapor into chamber. The engine is begging to run so I goes I will pull the head off and inspect the head gasket was soft and spongy and came apart in layers.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Re: Carb/Air flow problems on '62 Evinrude 3HP

That's way too low on the compression. I'm surprised it even tries to run.
 

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
Re: Carb/Air flow problems on '62 Evinrude 3HP

Yeah, so am I, but she will run for 3-8 seconds and then stop and she purrs smoothly otherwise. I will clean the head/piston heads and tomorrow and replace gasket and see how much it improves the compression. Hopefully that will help and she will respond and draw. It's a 1952 motor, I made a mistake on the entry when I started the thread, but I know the motor is pretty unchanged through those 2 decades. What is the ideal PSI for the Lightwin 3HP?
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Re: Carb/Air flow problems on '62 Evinrude 3HP

It should be somewhere around 80 PSI
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
Re: Carb/Air flow problems on '62 Evinrude 3HP

You may also want to try a different compression gauge. They can vary.
 

nwcove

Admiral
Joined
May 16, 2011
Messages
6,293
Re: Carb/Air flow problems on '62 Evinrude 3HP

just did a comp test on a jw-10 that hasnt been run for at least 15 years, 89 top, 88 bottom. but dont give up hope if you get numbers in the 60 psi range, as long as both holes are within a few psi of each other.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Re: Carb/Air flow problems on '62 Evinrude 3HP

It'll run at 60, but not as well as it should.
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
Re: Carb/Air flow problems on '62 Evinrude 3HP

I have got the low psi ones in the 60 range to run, but they usually require starting at a high throttle setting, and will not idle like one with 90 psi would. The higher compression JWS will idle down so nice you can almost count the RPMS!
 

nwcove

Admiral
Joined
May 16, 2011
Messages
6,293
Re: Carb/Air flow problems on '62 Evinrude 3HP

I have got the low psi ones in the 60 range to run, but they usually require starting at a high throttle setting, and will not idle like one with 90 psi would. The higher compression JWS will idle down so nice you can almost count the RPMS!

i sold a jw -20 two summers ago, that one would idle down so low that im sure you could've trolled for clams with it!!
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Re: Carb/Air flow problems on '62 Evinrude 3HP

guessing thorpe66 doesn't want to do a ring job just to prove a point with his father in law. agree 20psi won't do it, but 60 might. If the motor can be dialed in enough to get up to temp, compression check at that point (and subsequent to running) might be a lot better. And dad-in-law would be impressed. sounds like a head gasket might do the trick. I've got four of the little 3's, and I know one of them had cold compression around 50 or a little more, and ran well after the usual magneto and carb work.
 

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
Re: Carb/Air flow problems on '62 Evinrude 3HP

Thanks for the input, waiting on gasket to arrive (should be in by the end of week, and will let you know if the compression gets up there.
 

thorpe66

Cadet
Thread starter
Joined
Jan 17, 2014
Messages
12
Re: Carb/Air flow problems on '62 Evinrude 3HP

Head gasket and exhaust gasket replaced and compression jumped to 76-78 compression in both cylinders. Motor draws fuel and looks like a go for this one. Will adjust high and low needle valves when temp outside rises a little.
My father in-law will be impressed! Thank you for the insight and help.
 
Top