96 115 Johnson

Doublez

Cadet
Thread starter
Joined
May 25, 2017
Messages
6
I have a question and I'm hoping some of you guys can help me out. Yesterday I went fishing and the boat started fine and ran across the lake. Put the trolling motor in the water and fished for about an hour. Decided to move to another spot on the lake and he boat wouldn't start. I figured that the cranking battery was dead. Trolled back to the ramp and came home. When I got home I put a 12 hour charge on the battery. Went back out today, the boat started right up and then ran full throttle for about a mile, then the boat idled down and died kind of like it was out of gas. The. It wouldn't start, and I couldn't trim the motor. The gauges are working, but when I turn the key nothing. Trolled back to the ramp and had to manually release the trim to get the boat out of the water. What do you guys think could've caused this?
 

CaptnKingfisher

Petty Officer 1st Class
Joined
May 14, 2017
Messages
269
First I would check the condition of your battery. Do a voltage drop test during cranking (quick youtube search will give you a tutorial). If the voltage stays above 9.6 during cranking then the battery is still likely in good shape. If that's the case look for loose connections from your battery terminals to your starter solenoid. I doubt the issue is beyond the solenoid because otherwise when you turned the key to restart the engine, you would still hear the solenoid click. Under normal operation your stator generates AC current which your rectifier and regulator converts to DC and sends back through the battery cables to keep your battery charged. However if your battery is too weak, it may not be enough. You can test these components with a multimeter but I wouldnt due bother until I've inspected the battery.
 

CaptnKingfisher

Petty Officer 1st Class
Joined
May 14, 2017
Messages
269
By the way, I'm making an assumption here but I should ask for clarity: Are you running the trolling motor off of a separate battery?
 

Doublez

Cadet
Thread starter
Joined
May 25, 2017
Messages
6
Yes trolling motors are run off of a 24 volt system. The cranking battery is brand new. I am going to check the voltage tomorrow, and see how that does. The other question I have, could this have caused the motor to idle down and die?
 

CaptnKingfisher

Petty Officer 1st Class
Joined
May 14, 2017
Messages
269
Bad battery won't cause the motor to idle down, no. But the 'nothing happens when you turn the key' and boat 'idling down and stalling' seem to me like they are separate issues. Even if they are related, the power getting from your battery to your starter solenoid is a pretty simple process so that's a good spot to start with this problem. look around for frayed wires or weak connections while your at it. intermittent short somewhere maybe? anyone else have ideas?
 

Doublez

Cadet
Thread starter
Joined
May 25, 2017
Messages
6
Ok. So I have tested my battery and have 12.8 volts there, and I have 12.8 volts at the solenoid. The boat will not turn over and the motor will not trim. I checked the voltage at the trim switch on the motor and have 12.8 volts there. Any other ideas on next steps?
 

CaptnKingfisher

Petty Officer 1st Class
Joined
May 14, 2017
Messages
269
Turning the key while in neutral and nothings happening but your battery is good... okay so first thing I would check is the fuse inline with the solenoid. So look at your solenoid, there are two big terminals, and two smaller ones. One of the smaller ones is a ground, the other goes to the keyswitch in your control box. The red keyswitch wire has an inline 20 amp fuse. I suspect this fuse is blown. If its not blown, then Id check all of the wires on the solenoid are not frayed and have strong connections. At the very least you should hear the solenoid click when you turn the key. If this isnt the case, test your solenoid. A quick youtube search will tell you how
 

CaptnKingfisher

Petty Officer 1st Class
Joined
May 14, 2017
Messages
269
I hope someone else steps in though, I don't know why your trim isnt working when your switch has power. Ive never worked on a motor that new. I assume your model number is XJ112TSLEDR I'll look at the diagram and see if anything jumps out at me
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
Ok. So I have tested my battery and have 12.8 volts there, and I have 12.8 volts at the solenoid. The boat will not turn over and the motor will not trim. I checked the voltage at the trim switch on the motor and have 12.8 volts there.
When you were testing in each case where did you have the negative meter lead connected to?
This smells like a bad main ground at the battery or at the block or in the cable to me.
 

Doublez

Cadet
Thread starter
Joined
May 25, 2017
Messages
6
I haven't messed with it all day until just a few minutes ago. The first thing I did was turn the key on and then attempt a start, I heard the solenoid click, and then nothing. There are no frayed wires, connections are all good and the inline fuse is not blown.
 

Doublez

Cadet
Thread starter
Joined
May 25, 2017
Messages
6
Sorry, I just saw your post. I had it connected to the post, then I moved it along the cable as I checked it. I connected it to the negative post on the solenoid and on the block.
 

CaptnKingfisher

Petty Officer 1st Class
Joined
May 14, 2017
Messages
269
If the solenoid clicks when you turn the key but the starter doesnt engage then your starter is probably the issue. Have someone turn the key for you while you hold the multimeter red against the starter red terminal and black against a ground on the engine block. When the solenoid clicks your starter should get 12 volts from your battery. If your getting 12 volts at that spot during key turn but starter doesnt do anything, try adding a ground wire from the starter to the block to check if its a bad ground. If that doesnt help, its time to rebuild your starter or look for a new one. I think Fed is right though about this being a bad ground somewhere. These things we're talking about checking dont really help your OP post problems. Intermittent short or intermittent grounding issues
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
I would take some sandpaper to all of the wire connections, beginning with the battery leads (bend those a bit and listen for any crunching sounds -- corrosion, particularly if a salt water runner.)
 

Fed

Commander
Joined
Apr 1, 2010
Messages
2,457
I suspect you will find a high resistance connection breaking down under load.
You should re-test those places while someone actually turns the key to the start position.
Alternatively you can test for voltage drop (by the book) by testing across each connection while turning the key to the start position.
You will find that the voltage will drop between the solenoid positive & the block when the key is turned to start or the PTT is activated.

Edit: As suggested it could also be internally in the cable but this testing will pick it up and don't forget there's a difference between testing posts & cable lugs for example, testing across your battery posts may measure 12.8 V but testing across your battery lugs could easily show 0 Volts under load.
 
Last edited:

Doublez

Cadet
Thread starter
Joined
May 25, 2017
Messages
6
Update...I replaced the main lead from the battery and re-cleaned all connection points on the solenoid. That seemed to fix the problem of turning the boat over and the power tilt/trim. My next part will be to test the stator, as I expect it is going bad as well. Thanks for all the help and advice.
 
Top