93 115 johnson has shut down while wide open

Tylernpalmer

Cadet
Thread starter
Joined
Feb 23, 2017
Messages
7
It's done this to me twice. I'll be running along fine and dandy and then it's like it looses fuel and I've tried to feather the throttle trying to keep it running but failed both times. The odd part is when I go to start it again I have nothing. Turn the key and nothing. Both times I've pulled the cover off and crossed the solinoid with a screw driver and it fires right up and away we go again. Make it back to the docks and shut it down and hit the key it fires right back up. Is there a temp sensor or oil sensor that will cause this? I don't remember hearing the alarm either times but I was kinda in a panic to get it running again so may have missed it. And I can't repeat the issue it's very intermittent. Also time before last loading the boat on the trailer I would give it some throttle and it would die like it didn't have the power to push its self on the trailer. Any help is appreciated.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Some will argue.--------If it is a crossflow motor you start with a compression test.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
+1. Compression test first. Test thermo sensors - if it's overheating and locking up = bad. Starving for fuel also possible - try pumping primer ball when it's misbehaving.
 

Tylernpalmer

Cadet
Thread starter
Joined
Feb 23, 2017
Messages
7
I will do a compression check. But I doubt that it has low compression. It runs awesome. I just bought it this February and I'm running 50:1 pre mix while I'm making sure my vro is working correctly. I'm guessing that could be my power loss when I was trying to load it since it's probably running way to rich since it seems like the vro is working right. I'm just more worried about the random shut down. It didn't get hot and lock up. I'm not even sure it's getting hot. I know the alarm works I tested all of that stuff before I put it on the water at the beginning of the season. I'm thinking I'm going to wire a light in with the alarm so I will have a visual if something goes wacky. I'm not sure I could hear that alarm running down the river or lake.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Sounds like you're describing two problems. Time to break them down?

1) running WOT and it dies. Could be fuel starvation. Test by pumping primer ball when it's doing it. Double oiling won't do anything but make more smoke, or perhaps foul a plug.

2) won't crank after it dies (?) but will if you jump at the solenoid. Bad ignition switch? Broken wire in the wiring harness? I'd take my meter on the next trip and see if you get 12V on the small wire of the solenoid when trying to crank.
 

Tylernpalmer

Cadet
Thread starter
Joined
Feb 23, 2017
Messages
7
It's hard to diagnose because it does it randomly. And both times it's happened I needed it running to get out of the middle of the river. So I did what I had to to get it running. Will these shut down if a sensor is showing it's hot or low oil or something? Also the tach comes and goes but for the most part doesn't work. Kinda sounds like I've got a wiring problem.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Sensors are just information - they'll let you fry your motor if you ignore them.

Try moving the wiring around while underway (helper), especially the part that flexes in the motor well.
 

Tylernpalmer

Cadet
Thread starter
Joined
Feb 23, 2017
Messages
7
Ok. I will try that. Hopefully I can narrow it down. I'm planning on taking it out fishing this weekend and I'm hoping I don't run into problems again but if I do it won't be a busy river so I should be able to diagnose it.
 

Tylernpalmer

Cadet
Thread starter
Joined
Feb 23, 2017
Messages
7
Well I ran it this evening, ran decent other then fouling plugs. I'm guessing the oil injection is working. But still could barely get itself on the trailer. I put new plugs in it and some sea foam in it, will see how it does in the morning. How do I check the timing advance on it? I know tdc should be lined up with the pointer when at tdc. But what about when it's full throttle? 28* is marked white.....
 
Top