90 evinrude won't WOT after ideling

Ktms450r

Recruit
Thread starter
Joined
Aug 21, 2016
Messages
5
I have a 1990 30hp evinrude. It will start and idle all day but if you idle more than a few minutes and go to WOT the motor acts like bogs and revs continuously until I return throttle to idle. Sometimes it will do this few times before running correct. there has been a few weekends I've had no issues. Just want it to be dependable! I've replaced all fuel lines, fuel pump, spark plugs.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Check for a spun prop hub. Mark inner hub, mark outer hub, run, compare marks
 

Ktms450r

Recruit
Thread starter
Joined
Aug 21, 2016
Messages
5
Ok . I'll give that a try next weekend. It acts like loosing spark or fuel. The problem occurs after ideling for a bit then throttle is great till 1/4 then is like a rev limiter is kicking in. It will rev then bogg until I back the throttle down to 1/4 throttle. And after a few times everything is back to normal until I stop and idle to check bank poles.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Are you getting an alarm? Post model#

Could it be overheating? Pee stream tells little.

Is there a tan wire that goes into the power pack?
 

Ktms450r

Recruit
Thread starter
Joined
Aug 21, 2016
Messages
5
model number e30teess 1990 evinrude electric start.. this motor did set for a few years before i purchased it.

what alarm would i listen for? the pee stream is good and warm but not hot by any means.

I will look for the tan wire tonight.

Thanks
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
I just cant remember if that has slow system. Some models have a rev limiter that kicks in if it detects no oil or overheat.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Should replace the impeller, and check spark with a spark tester. But it does sound like a spun hub, as mentioned.
 

Ktms450r

Recruit
Thread starter
Joined
Aug 21, 2016
Messages
5
the motor has spark it will run and drive my problem is very interment. it will happen once or twice on a whole day on the water.
you think the impeller is the problem or maintance item?.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
I would just run the usual battery of tests. Pick up an adjustable open-air spark tester ($10) and a compression tester -- buy or borrow. I would also get and infrared heat gun and check temp at the top of the head (look for 130-150F -- should not exceed 160). You should see about a half inch spark -- also possible spark is dropping out on one cylinder when it "bogs". Pull off the boots one at a time to see if one of the cylinders is dropping out. If it has been a while since the impeller was replaced or the rig is new to you, replace the impeller. But do the prop check described in #2.
 

Ktms450r

Recruit
Thread starter
Joined
Aug 21, 2016
Messages
5
Well I put a new installed new thermostat. The old was opening at 200. That didn't fix it. So I took impeller off to inspect it and it was destroyed. I put a new one in and now will take off after ideling and runs smoother. Thanks for the help
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Compression test should be done !----The head bolts may be loose.----The head will be warped !!----Time to install a new head gasket too.---Some will argue on the need to do this maintenance.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Compression test should be done !----The head bolts may be loose.----The head will be warped !!----Time to install a new head gasket too.---Some will argue on the need to do this maintenance.

Now that you have found a bad impellar and we know it was hot racerone has given you "must do" advice.
 
Top