83 115 crossflow identification?

Winstonk24

Recruit
Thread starter
Joined
Mar 1, 2016
Messages
3
Picked up what I thought was a 88hp SPL. Turns out the vin says it's a 83 115!!

Is there any sure way to tell if its a 115? We don't know if the bottom bracket is original... The cowling said 88 SPL.... The freeze plugs have no numbers and the carb number on top doesn't give me any conclusions. Could I measure the carbs? I know this year didn't have bubbleback..


Any info on this engine? Has good compression. 120-125 all 4. Good spark. Guy says it ran great before...guy is a boat mechanic. A history lesson would be awesome. Putting it on a 16' hydra sport center concol. Shooting for 55mph
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
I'd spend some time looking at the factory exploded parts diagrams. Compare those diagrams to your engine. Here is the website: epc.brp.com. Some things I'd pay attention to: 1. The heads on the block. Your compression numbers would seem to indicate that they are an older variety, providing you with the strong compression numbers that you posted. Verify the head numbers on your block with the parts diagrams. 2. 1983 was the last year for the old-style single fuel pump. In 84 the VRO came out. 3. 83 was a change year for the carbs. Mid-year the design changed-a plate was added to the top of the carbs. 4. That 83 engine was the last 115 that had separate rectifier and voltage regulator. In 1984 they were combined into a single unit, were water cooled and sat atop the block. 5. Most likely the powerhead will be painted the same color as the cowling. Later blocks were painted all black. 6. Power trim unit. The motor is the later design, with two wires and two relays. The relays were inside a separate control box. 7. That engine had the rubber intake filler blocks. Good for 3-5 hp. Not easy to detect these blocks, as they sit behind the intake manifold and you have to take that off to see them.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
What is the dimension of the carb throats? Should be cast into the face of the carb. Something like 1-1/4 or 1-5/16. If it does in fact have 1-5/16 carbs, it is likely a 115. Smaller bore than that is something else... This ASSUMES that the motor hasn't been cobbled together beyond a different cowling being plopped on top.

Out of curiosity, what is the hp rating on the boat? Not uncommon for someone to use a lower rated cowling to avoid the eyes of Johnny Law if he has a 115 mounted on a boat rated for 90...
 
Last edited:

Winstonk24

Recruit
Thread starter
Joined
Mar 1, 2016
Messages
3
Don't know what boat it came from. Mine is only rated for a 70 though... I might leave the 115 stickers I ordered off or remove the plack from my boat. I'm in the process of painting it.

I'll get some pictures of the engine. Thanks for the replys you guys are a gold mine of info.

The entire engine block and heads are black. There is no numbers on the top freeze plugs either.

I'll post more info when I have a chance to look at it today.
 

Winstonk24

Recruit
Thread starter
Joined
Mar 1, 2016
Messages
3
1 3/16 is the carb size
 

Attachments

  • 14569506409651410723831.jpg
    14569506409651410723831.jpg
    254.9 KB · Views: 0
  • 1456950940289-2044439326.jpg
    1456950940289-2044439326.jpg
    240.4 KB · Views: 0
Top